Направљене поруке на форуму
-
Чланци
-
Ajde da ne otvaram novi topic…Mlatio sam se sa fedorom jes nekoliko dana i resio da vratim gentoo.Stavim ja lepo gentoo instaliram drivere za modem,ucita lepo module, kad da se konektujem sve se ukoci bas kao i kod fedore.Sta je sad tu problem da li driver alk-8 ne valja ili meni nesto od hardvera nije u redu…ili pak nesto drugo.
Nisam dugo bio na forumu…svasta se ovde promenilo…nego da predjem na stvar.Odustao sam bio od fedore jer mi riknuo hdd.Kupio sam drugi i rekoh ajde da probam ponovo da vidim hoce li modem da proradi(radio na svim distroima ali na fedori nece i to ti je).Ucitao sam nekako modul za modem ali se sada javlja drugi problem: upisem user name,password,pocne da se konektuje, stigne do kraja,pise loging to network i tras! ceo sistem se ukoci i mora restart.Pogledam log file i u njemu nema nikakve greske.Pise samo pppd starting i to je sve.Kada pokusam da uradim debug na pppd opet se sistem ukoci.Reinstalirao sam pppd i nista.Ne znam sta da mu radim???
Updateovao sam i binutils i file ali ot toga nema nista sve je isto.Trazio sam po netu ali za fc5 nema niko resenje.Probacu da se mlatim sa martian driverom ali mislim da taj driver ne odgovara mom modemu.
Nece i to ti je.Probao sam gomilu drivera i sa svima je ista prica.Cackao sam po internetu nisao na gomilu ljudi koji imaju ovakav problem ali niko nezna resenje.
Updateovao sam kernel ali opet ista prica.Evo sta kaze dmesg:
[code]Linux version 2.6.16-1.2080_FC5 ([email protected]) (gcc version 4.1.0 20060304 (Red Hat 4.1.0-3)) #1 Tue Mar 28 03:38:34 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 – 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 – 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 – 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 – 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 – 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 – 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 – 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 – 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 – 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
found SMP MP-table at 000f4cd0
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:0
DMA32 zone: 0 pages, LIFO batch:0
Normal zone: 61424 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:0
DMI 2.3 present.
ACPI: RSDP (v000 GBT ) @ 0x000f6640
ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x0fff3000
ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x0fff3040
ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x0fff72c0
ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore… done.
Enabling unmasked SIMD FPU exception support… done.
Initializing CPU#0
CPU 0 irqstacks, hard=c03d4000 soft=c03d3000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1473.754 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80×25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254748k/262080k available (1914k kernel code, 6664k reserved, 774k data, 176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode… Ok.
Calibrating delay using timer specific routine.. 2951.47 BogoMIPS (lpj=5902945)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f3ff c1cbfbff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 1700+ stepping 02
Checking ‘hlt’ instruction… OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs… it is
Freeing initrd memory: 899k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfa110, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 16 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn’t work, try “pci=routeirq”. If it helps, post a report
pnp: 00:02: ioport range 0x4000-0x407f could not be reserved
pnp: 00:02: ioport range 0x40f0-0x40ff could not be reserved
pnp: 00:02: ioport range 0x5000-0x500f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e0000000-e1ffffff
PREFETCH window: d8000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1145137274.620:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
– Added public key 8227E1D7AAD49D08
– User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Bypassing VIA 8237 APIC De-Assert Message
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards…
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 16
PCI: Via IRQ fixup for 0000:00:0f.0, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0…
hda: Maxtor 6E040L0, ATA DISK drive
hdb: WDC WD400BB-00DEA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1…
hdc: ASUS DRW-1608P2, ATAPI CD/DVD-ROM
drive
hdd: ASUS CRW-5232AS, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 78154175 sectors (40014 MB)
native capacity is 78156288 sectors (40016 MB)
hda: Host Protected Area disabled.
hda: 78156288 sectors (40016 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2
hdb: max request size: 128KiB
hdb: Host Protected Area detected.
current capacity is 78163247 sectors (40019 MB)
native capacity is 78165360 sectors (40020 MB)
hdb: Host Protected Area disabled.
hdb: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hdb: cache flushes not supported
hdb: hdb1 hdb2 hdb3
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 6, 327680 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Processor cpuid 662 not supported
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 UAR1 LPT1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 176k freed
Write protecting the kernel read-only data: 359k
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 17
eth0: RealTek RTL8139 at 0xd0872000, 00:0d:61:be:90:c0, IRQ 17
eth0: Identified 8139 chip type ‘RTL-8101’
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 18
PCI: Via IRQ fixup for 0000:00:11.5, from 11 to 2
PCI: Setting latency timer of device 0000:00:11.5 to 64
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 0, using IRQ 21
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.0, from 5 to 3
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 19, io base 0x0000dc00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 3
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 19, io base 0x0000e000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2 -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.2, from 5 to 3
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 19, io base 0x0000e400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 19
PCI: Via IRQ fixup for 0000:00:10.4, from 11 to 3
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.4: irq 19, io mem 0xe2001000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Non-volatile memory driver v1.2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun …
md: … autorun DONE.
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: [email protected]
EXT3 FS on hdb2, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 522104k swap on /dev/hdb3. Priority:-1 extents:1 across:522104k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (2047 buckets, 16376 max) – 232 bytes per conntrack
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
ppdev: user-space parallel port driver
ppdev0: registered pardevice
ppdev0: unregistered pardevice
ppdev1: claim the port first
ppdev2: claim the port first
ppdev3: claim the port first
ltmodem: module license ‘Proprietary’ taints kernel.
ltmodem: falsely claims to have parameter vendor_id
ltserial: Unknown symbol lt_get_modem_interface
ltmodem: falsely claims to have parameter vendor_id
ltmodem: falsely claims to have parameter vendor_id
ltserial: Unknown symbol lt_get_modem_interface
ltmodem: falsely claims to have parameter vendor_id
ltserial: Unknown symbol lt_get_modem_interface[/code]Koliko vidim nema nikakvih bagova sve zivo melje a uz to se ne koci ni malo
Sta da se koci na takvoj masini…
