Ћирилица

[MarkoFLOJD]

MDK10.1 nemam, tako da me zanima kako (kad i gde se to bira) da pokrenem MANDRIVU sa 2.4 kernelom – da li je to prilikom bootovanja-logovanja (sto bi bilo dobro), ili moram da ga preinstaliram pa negde u toku instalacije moram nesto da uradim…?

Jos jednom HVALA!

Marko

[MarkoFLOJD]

Koliko vidim iz ovog ispada jedino pomaze da promenim modem ili LINUX – kad smo kod toga sta mislite o tome da deinstaliram MANDRIVU i da ponovo instaliram MDK9.1???

[MarkoFLOJD]

a da, poslao sam ovaj fajl po uputstvu na diskution list…

[MarkoFLOJD]

Milose, evo odradio sam i dobi ModemData.txt:

DO use the following line as the email Subject Line, to alert cogent experts:
scanModem, Mandrakelinux release
Kernel 2.6.11-6mdk kernel 2.6.11-6mdk
Occassionally reponses are blocked by an Internet Providers mail filters.
So do in a day also check the Archived responses at [email protected]
Code updated on: 2005_June_02
———— ————– System information ————————
Mandrakelinux release 10.2 (Limited Edition 2005) for i586
Kernel 2.6.11-6mdk on an i686 /
distro=
on System with processor: i686
currently under kernel: 2.6.11-6mdk

There are emerging complications under 2.6.10 and later kernels. Concerning code for:
Smartlink slmodem :
slmodem-2.9.9d.tar.gz at http://linmodems.technion.ac.il/packages/smartlink/
has the current fixes. Related messages are:
http://www.datiku.com/documents/2610_migration.php
http://www.ussg.iu.edu/hypermail/linux/kernel/0409.3/0345.html
http://linmodems.technion.ac.il/archive-fourth/msg03736.html .
http://linmodems.technion.ac.il/packages/smartlink/ has an upgrab-winmodem.tar.gz,
providing a driver to alleviate inappropriate capture of a winmodem by a serial port driver.
Lucent/Agere DSP/ltmodem:
http://linmodems.technion.ac.il/archive-fourth/msg03733.html
Concerning Intel-536ep and 537
http://www.ubuntulinux.org/wiki/IntelFiveThreeSixEPModemHowto/
http://linmodems.technion.ac.il/archive-fifth/msg00280.html
http://linmodems.technion.ac.il/archive-fifth/msg00881.html

The kernel was assembled with compiler: 3.4.3
with current System compiler GCC=3.4.3
/usr/bin/gcc -> /etc/alternatives/gcc

Checking for kernel-headers needed for compiling.
kernel-headers have base folder /lib/modules/2.6.11-6mdk/build
kernel-headers have base folder /usr/src/linux
kernel-headers have base folder /usr/src/linux-2.6.11-6mdk

A /dev/modem symbolic link is not set.
Checking for /dev/tts/ devices
total 0
lrwxrwxrwx 1 root root 8 Jun 12 19:11 0 -> ../ttyS0
lrwxrwxrwx 1 root root 8 Jun 12 19:11 1 -> ../ttyS1
lrwxrwxrwx 1 root root 8 Jun 12 19:11 2 -> ../ttyS2
lrwxrwxrwx 1 root root 8 Jun 12 19:11 3 -> ../ttyS3
lrwxrwxrwx 1 root root 8 Jun 12 19:11 4 -> ../ttyS4
lrwxrwxrwx 1 root root 8 Jun 12 19:11 5 -> ../ttyS5
lrwxrwxrwx 1 root root 8 Jun 12 19:11 6 -> ../ttyS6
lrwxrwxrwx 1 root root 8 Jun 12 19:11 7 -> ../ttyS7

USB modem not detected.

For Mandrake 9.1 later, installation of the pciutils.rpm package providing lspci is necessary.
The installed utility lspcidrake is NOT an adequate alternate for scanModem support.

00:05.0 Multimedia audio controller: nVidia Corporation nForce Audio Processing Unit (rev a2)
00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)

Modem candidates are at PCI_buses: 01:0b.0

Providing detail for device at 01:0b.0
with vendor-ID:device-ID
—-:—-
Class 0780: 1813:4000 Communication controller: Ambient Technologies Inc HaM controllerless modem (rev 02)
SubSystem
Flags: medium devsel, IRQ 5
Memory at da000000 (32-bit, non-prefetchable)

—–PCI_IDs——- –CompilerVer-
Feature List: Primary Subsystem Distr KernelVer kernel default CPU
./scanModem test 1813:4000 mandrake 2.6.11-6mdk 3.4.3 3.4.3 i686

Information on several modem chipset providers is provided below,
because ambiguities remain on the correct choice of supporting software.

== Checking PCI IDs through modem chip suppliers ==

Vendor=1813 Ambient Tech was acquired by Intel with its HaM (Host assisted Modem) chipsets.
Intel-v92ham-453.tgz ifor 2.4.n kernels is FINAL update for HaM modems, available at:
http://linmodems.technion.ac.il/packages/Intel/ham/
http://developer.intel.com/design/modems/support/drivers.htm
It is NOT functional when compiled under 2.6.n kernels and will NOT be updated to support
the 2.6.n kernels, Intel maintainer Dorian Araneda has reported.
But under the 2.4.nn kernels, all HaM chipsets are supported,
with a single EXCEPTION: the odd PCI_ID 1813:4100 modems. For the explanation, see message:
http://linmodems.org/cgi-bin/ezmlm-cgi?1:mss:9448:200210:fbhcoigfcimgkjdedjad

Vendor=8086 is Intel, Inc. producing HaM and 536ep host controller free (HCF) modems, 537 soft modem
and AC97 and MC97 controllers managing a varierty of non-Intel soft modem Subsystems.
These subSystems often have PCI_IDs assigned by the modem assembler, rather than the chip provider.
Download available drivers through: http://developer.intel.com/design/modems/support/drivers.htm with Intel-537 types at:
http://downloadfinder.intel.com/scripts-df/Filter_Results.asp?selCat=all&strOSs=39&ProductID=1230&page_nbr=2
Also check at: http://linmodems.technion.ac.il/packages/Intel/537/
for beta releases and perhaps Already compiled drivers for some Linux distributions
A very detailed installation report cogent to 537 type modems is at:
http://linmodems.technion.ac.il/archive-fifth/msg00541.html
Setup call id with:
Type 1 : When the phone line is not in use at+vcid=1
Type 2 : When the phone line is already in use on a call at+pcw=0
———————

======= PCI_ID checking completed ======
Update=2005_June_02
A PCMCIA CardBus is not detected on this System.
GCCversion=3.4.3

For information on modem port creation under the UDEV device file system see:
http://linmodems.technion.ac.il/archive-fourth/msg03299.html for Conexnant modems
http://linmodems.technion.ac.il/archive-fifth/msg01177.html for Lucent/Agere DSP modems

The following information blocks just query some ppp support items.

====================================================
grep -rs ppp /etc/modprobe.*
————————————-
/etc/modprobe.devfs:alias /dev/ppp* ppp_generic
————————————-

The following ppp related modules should be unpacked by root with:
# gunzip PathTo/ModuleName.ko.gz
—————————————-
/lib/modules/2.6.11-6mdk/kernel/drivers/net/bsd_comp.ko.gz
/lib/modules/2.6.11-6mdk/kernel/drivers/net/ppp_async.ko.gz
/lib/modules/2.6.11-6mdk/kernel/drivers/net/ppp_generic.ko.gz
/lib/modules/2.6.11-6mdk/kernel/drivers/net/slhc.ko.gz
/lib/modules/2.6.11-6mdk/kernel/drivers/net/ppp_deflate.ko.gz
/lib/modules/2.6.11-6mdk/kernel/lib/zlib_deflate/zlib_deflate.ko.gz

On most Systems, this will driven by installing the wvdial.rpm
and the package providing the KPPP graphical dialing interface.

—-active COMM services are ————
eth0 Link encap:Ethernet HWaddr 00:04:61:61:BD:5A
inet6 addr: fe80::204:61ff:fe61:bd5a/64 Scope:Link
eth1 Link encap:UNSPEC HWaddr 00-04-61-00-00-07-77-3B-00-00-00-00-00-00-00-00
sit0 Link encap:IPv6-in-IPv4
This COMM mode should be closed before using the modem, or DNS services may fail.
Be sure to read the Ethernet section of Modem/YourModem.txt
DEVPPP=crw——- 1 root root 108, 0 Jun 12 19:11 /dev/ppp
A /dev/modem symbolic link is not present

No devfsd.conf file found, indicated absense of the devfsd daemon package
for device file system (devfs) symbolic link support.

DEVFSD=
—- dmesg queries ——-

In the Mandrake installation disks do not include the dialer utility wvdial.rpm,
then get instructions from http://linmodems.technion.ac.il/archive-fifth/msg01480.html

Sta dalje?

[MarkoFLOJD]

Verovatno sam trebao da naglasim da neznam da radim pod linuxom, te se izvinjavam i molim za malo vise strpljenja, kako bih mogao da razumem ono sto mi savetujete.

milosk mi je rekao da odradim scanmodem, ali kako vidim radi se o nekom GZ fajlu – verovatno je to neka linux aplikacija koju nakon sto se prebacim sa windowsa na linux treba da je instaliram i pokrenem a ona ce da mi da tacne podatke o mom modemu? (ako sam lepo shvatio tako cu i da uradim pa cu da ti javim…)

za mtm76: otvorio sam modprobe.conf i u njemu je imalo samo:
# This file is autogenerated from /etc/modules.conf using generate-modprobe.conf command

alias eth0 forcedeth
alias sound-slot-0 snd-intel8x0
remove snd-intel8x0 /sbin/modprobe -r snd-pcm-oss; /sbin/modprobe –first-time -r –ignore-remove snd-intel8x0
install snd-intel8x0 /sbin/modprobe –first-time –ignore-install snd-intel8x0 && { /sbin/modprobe snd-pcm-oss; /bin/true; }
install usb-interface /sbin/modprobe ohci-hcd; /sbin/modprobe ehci-hcd; /bin/true
alias eth1 eth1394
alias ieee1394-controller ohci1394
options bttv radio=1 gbuffers=4

i nista vise! Ja sam uzeo i dodao u nastavku tekst-kod koji si mi poslao ali nikakvih promena nije bilo kada sam ponovo pokrenuo bilo koju od TV aplikacija (uzgred koju mi preporucujes – koju ti koristis, i koje parametre treba unutar njih da koristim pal, ppal600, ili neki drugi, ulazni link je Television a ne coax1,3, i region Eastern ili western Europe).
Ovo sto si mi u medjuvremenu poslao zaista ne razumem – sta da radim dalje?

HVALA! 🙂

Marko

[MarkoFLOJD]

Pogledao sam i nasao adresu http://linmodems.technion.ac.il/packages/Intel/ koji je FTP fazonu, i moram da Te (milosk) zamolim da mi pomognes:
– kad sam nekad ranije gledao modem na sebi ima neki …536… cip, ali ga vindovs vidi kao “Intel V92 HaM DataFaxVoice”, a na adresi koju si mi poslao pise:
“Modems based on Intel chips (HaM/536ep/537).
Intel 537 kernel 2.6 available under Intel/537 courtesy of Alexander Komarov – 13/8/04 (not yet on Intel site)
The Intel HaM Driver version 3.33 is the only version to work with 2.2.x kernels.
New Linux modems drivers (536,537) are posted on the Intel Web site.
Many older installers are also stored on this site
See both locations (specially bottom of Intel site) for some ready-to-go packages
You still may want to note that the SmartLink slmdm driver up to release 2.7.10 or starting from 2.9.1, not those in between, usually supports this chip
Dorian Araneda’s latest official release driver tarball for Intel’s HaM-V92 and 536ep modems, supporting kernels 2.4.x.
Please make sure to download the right driver. The HaM-V92 driver and the 536ep driver are NOT interchangeable.
Instructions available in file readme.txt therein and here.
Former versions and sample precompiled ready-to-go tarballs are also available at the same place.
An official Intel page exists for these drivers, with some delay in updating.
Voice features identification: see CrystalHaM and SilabHaM views.

Intel 536EP: Honestar has the 4.25 beta version for the 536EP posted– please see: description and link.”
…dok tamo na adersi koju sam ti poslao ima grupa HaM (valjda za 2.4) i grupa 536 za koju pise da su to drajveri za 2.6 kernele (a meni valjda treba za 2.6?), pa te molim da pogleas i da mi kazes koji onda je za mandrivu od ovih 536 drajvera i da li uopste mogu da ih koristim? (nadam se da nisam bio previse konfuzan i da si me razumeo… 🙂 )

A sto se mtm76 odgovora tice, koliko am Te razumeo ovo sto si napisao se odnosi na TV karticu (veruj mi, gledao sam…) – probacu pa cu da ti javim dal’ je uspelo – HVALA TI – i da sta je sa radio opcijom za ovu karticu?

Marko

[MarkoFLOJD]

Instalirao sam i Crossover3.0 (koji sam dobio na disku EMULATORI sa sajta-moja predlog je da se tu doda i WineTool, i ostale stvari koje se pominju i preporucuju na forumima vezanim za emulatore) i proradio je i Wine, mada jos nisam uspeo ono sto sam i sa emulatorima i nameravao – ali se nadam da cu i to…

A i sto se ostalih stvari tice stvarno mi treba pomoc pa

LJUDI POMAGAJTE VEC JEDNOM – PLEASEEEEEEEEEEEEEE !!! 🙂

Marko

[MarkoFLOJD]

Znaci MANDRIVA ?!

A sta je sa ovim pricama da nakon Mandrake 9.1 su nove verzije nesto kao nestabilne itd… ?

Usput hvala na poucnoj diskusiji… 🙂

Marko

[MarkoFLOJD]

Prvo veliko HVALA na odgovorima!!!
Drugo, izvinjavam se na smetnji, ali normalno da sam predhodno prvo iskoristio pretrazivanje, ali sem
http://www.linuxo.org/modules.php?name=Forums&file=viewtopic&t=3697
nisam nasao nista sto bi mi zaista pomoglo, te sam zbog toga i postavio pitanje.
Ustalom zato i Vi jeste VELEMAJSTORI a ja nisam ! 🙂
E sad sustina:
Naime imam neku svoju aplikaciju koja je pisana u VB6 koja koristi Access bazu i ima komunikaciju sa jednim uredjajem preko COM porta, tako da sada gledam da li lako mogu da “prenesem” tu svoju aplikaciju na Linux te odatle slede pitanja:
– da li postoji neki linux-basic kompajler koji moze moj .vbp (sa svim .frm fajlovima) da prosto iskompajlira da dobijem “.exe” fajl za Linux platformu?
– shodno tome koji bi to Linux-Basic kompajler bio (pogledao sam za gambas ali tamo pise da ima neke probleme sa Mandrake linuxom) – takodje na adresi http://www.thefreecountry.com/compilers/basic.shtml ima gomila linkova za gomilu Basic-a, pa koji bi bio najpogodniji za ovako nesto ?
– prvo neznam da li bi u tom slucaju mogao dalje da koristim bazu u postojecem Access obliku ili bih morao da je nekako (takodje neznam kako) “konverujem” u MySQL format, a i nisam radio sa MySQL-om, pa neznam kako ide komunikacija-vezivanje-otvaranje MySQL baze iz VB-aplikacije ?

Opet unapred HVALA na pomoci – mnogo bi mi znacilo da ove neke stvari rascistim u svojoj glavi pre nego se bacim u to…

Marko

[MarkoFLOJD]

Nije valjda da niko nezna … 🙁

[Аутор]

Чланци