Ћирилица

[dokman]

Hvala, nadam se da cu uraditi nesto.

[dokman]

Uradio sam taj 4.2, posto je kod mene gcc4.2.4, zavrsi on to, ja pokusam da konfigurisem wvdial kad ono
[code]wvdialconf /etc/wvdial.conf
Editing `/etc/wvdial.conf’.

Scanning your serial ports for a modem.

Modem Port Scan: S0  S1  S2  S3

Sorry, no modem was detected!  Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://open.nit.ca/wiki/?WvDial

If you still have problems, send mail to .[/code]

nema mi nigde modema, sakrio se.

zato ti kazem da mi napises korak po korak, zamolio bi i cime se konektujes, koja je komanda za uspostavljanje veze itd.

ovo je iz
[code]lspci
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC’97 Modem Controller (rev 03)[/code]
tako vidi modem, jel isto i kod tebe?

[dokman]

Dede, Jovire reci mi “step by step” kako si osposobio svoj modem, PLEASE! Popizdi vise!

Probao sam onaj SLMODEMD.gcc4.1 i 4.2, u oba mi na
[code]make[/code]
izbacuje
[code]make: *** No targets specified and no makefile found.  Stop.[/code]

kao ne postoji “make” file, a u README pise da se on po potrebi menja ako nije dobro upisana putanja do kernela!

Nemam ideje!

Unapred hvala!

[dokman]

Kako je ljudima dobro! Ovo je pocetak novog Reda Slobodnih Zidara, u najmanju ruku!
Jos da je Tito ziv pa da poverujem!

[dokman]

Sretna Nova 2010. godina i sve najlepse SVIMA!!!

[dokman]

Upisao sam i jedno i drugo, opet isto.

Citao sam malo pazljivije tvoj prethodni post, da u boot.txt ima resenje za cudnu stvar koja se desava kod mene, u dmesg sam nasao
[code]slamr: module license ‘Smart Link Ltd.’ taints kernel.
slamr: SmartLink AMRMO modem.
slamr: probe 8086:24c6 ICH4 card…
slamr 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
slamr 0000:00:1f.6: setting latency timer to 64
slamr: mc97 codec is SIL22
slamr: slamr0 is ICH4 card.[/code]
probao sam naci neko objasnjenje na netu za to, ali nisam uspeo, jos pise da se moze u bootloader u kernel liniju dodati
[code]pci=routeirq[/code]
ili
[code]pollirq[/code]
ali opet bez uspeha, izgleda da se zbog necega u toku boot-a desava
[code]WvModem: Cannot get information for serial port[/code]
kad udarim
[code]wvdialconf[/code]

Ne da mi se pa to ti je!

[dokman]

Zasto se ovo desava
[code]root@dokman:/home/dokman# wvdialconf /etc/wvdial.conf
Editing `/etc/wvdial.conf’.

Scanning your serial ports for a modem.

Modem Port Scan: S0  S1  S2  S3
WvModem: Cannot get information for serial port.
ttySL0: ATQ0 V1 E1 — OK
ttySL0: ATQ0 V1 E1 Z — OK
ttySL0: ATQ0 V1 E1 S0=0 — OK
ttySL0: ATQ0 V1 E1 S0=0 &C1 — OK
ttySL0: ATQ0 V1 E1 S0=0 &C1 &D2 — OK
ttySL0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK
ttySL0: Modem Identifier: ATI — SmartLink Soft Modem
ttySL0: Speed 4800: AT — OK
ttySL0: Speed 9600: AT — OK
ttySL0: Speed 19200: AT — OK
ttySL0: Speed 38400: AT — OK
ttySL0: Speed 57600: AT — OK
ttySL0: Speed 115200: AT — OK
ttySL0: Speed 230400: AT — OK
ttySL0: Speed 460800: AT — OK
ttySL0: Max speed is 460800; that should be safe.
ttySL0: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 — OK

Found a modem on /dev/ttySL0.
Modem configuration written to /etc/wvdial.conf.
ttySL0: Speed 460800; init “ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0”
root@dokman:/home/dokman#[/code]

mislio sam da je bog onoga sto u toku boot-a iskljuci slamr pa ga ponovo ukljuci, pa sledeci put odradim
[code]root@dokman:/home/dokman# rmmod slamr
root@dokman:/home/dokman# modprobe slamr
root@dokman:/home/dokman# mknod -m 600 /dev/slamr0 c 242 0
root@dokman:/home/dokman# /usr/sbin/slmodemd -c BULGARIA /dev/slamr0
SmartLink Soft Modem: version 2.9.11 Dec 14 2009 00:47:22
symbolic link `/dev/ttySL0′ -> `/dev/pts/2′ created.
modem `slamr0′ created. TTY is `/dev/pts/2′
Use `/dev/ttySL0′ as modem device, Ctrl+C for termination.[/code]
ali svejedno, nista se ne menja.

A wvdial kad pokrenem
[code]root@dokman:/home/dokman# wvdial
–> WvDial: Internet dialer version 1.60
–> Cannot get information for serial port.
–> Initializing modem.
–> Sending: ATZ
ATZ
OK
–> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
–> Modem initialized.
–> Sending: ATDT042110011
–> Waiting for carrier.
ATDT042110011
NO CARRIER
–> No Carrier!  Trying again.
–> Sending: ATDT042110011
–> Waiting for carrier.
ATDT042110011
–> Timed out while dialing.  Trying again.
^CCaught signal 2:  Attempting to exit gracefully…
–> Disconnecting at Thu Dec 17 11:49:01 2009
root@dokman:/home/dokman#[/code]

i ovaj Waiting for carrier. se ponavlja u nedogled.

[dokman]

Uspeo sam srediti ovo sto sam zabrljavio, ali jos uvek ostaje problem, postoji li nacin da se ovaj salmr0 automatski pravi pri boot-u, pokusavao sam naci neko resnje na netu ali nema ili ja trazim na pogresnom mestu?

[dokman]

Napravio sam sranje, upisao sam u /etc/rc.d/rc.local
[code]mknod -m 600 /dev/slamr0 c 242 0
/usr/sbin/slmodemd –country=USA /dev/slamr0[/code]

sad pri boot-u izbacuje
[code]SmartLink Soft Modem: version 2.9.11 Dec 14 2009 00:47:22
symbolic link `/dev/ttySL0′ -> `/dev/pts/2′ created.
modem `slamr0′ created. TTY is `/dev/pts/2′
Use `/dev/ttySL0′ as modem device, Ctrl+C for termination.[/code]
i tu stane.

koji je postupak da sa livecd-a podignem sistem i editujem ovaj rc.local file i izbrisem
[code]/usr/sbin/slmodemd –country=USA /dev/slamr0[/code] ?

mislim da ce to resiti problem, bar da podigne sistem?!

[dokman]

dobro, to se onda da resiti!

kad u KPPP idem na connect, ide modem ready, dailing 042…, initializing modem i tu stane, mogu da ga prekinem u bilo kom trenutku, a komp radi normalno.
query modem radi cini mi se normalno

[Аутор]

Чланци