Направљене поруке на форуму
-
Чланци
-
Zvuka nemas zato sto nisi u audio grupi. Dodaj korisnika u audio grupu uz pomoc KUser-a (tako ti je najlakse) ili komandom gpasswd. Preporucio bih ti jos da ga ubacis u grupe cdrom, video i power.
Namestio sam,radi sad.
Hvala ! 🙂Da li je korisnik (nebojsa) clan audio grupe? Ukucaj u konzoli:
[code] nebojsa@shadow:~$ groups nebojsa
nebojsa : users plugdev
nebojsa@shadow:~$ [/code]ovo mi izbaci…
[code] nebojsa@shadow:~$ kdesu kwrite
nebojsa@shadow:~$ [/code]Ovde mi izbaci prozor sa passwordom,ubacim sifru (root) i otvori mi kwrite…
I proradio mi je kwrite….:)
Ali zvuka i dalje nemamAe nemoj da pokreces kwrite kao root nego kao korisnik koji je pokrenuo X sezonu. Moguce je da ti fali autorizacija na X serveru. Dakle, `startx` kao korisnik, otvori emulator terminala i u njemu `kwrite`. Nista vise.
Otvara mi kwrite kao obican user na runlevel 4,a na root-y nece…
Druga stvar, pogledaj sta ti se od skripti pokrece u kom runlevelu. Mozda fali nesto od skripti sto ucitava module za ALSA-u u 4. nivou.
eo cela lista iz inittab-a…:
[code]
# These are the default runlevels in Slackware:
# 0 = halt
# 1 = single user mode
# 2 = unused (but configured the same as runlevel 3)
# 3 = multiuser mode (default Slackware runlevel)
# 4 = X11 with KDM/GDM/XDM (session managers)
# 5 = unused (but configured the same as runlevel 3)
# 6 = reboot# Default runlevel. (Do not set to 0 or 6)
id:3:initdefault:# System initialization (runs when system boots).
si:S:sysinit:/etc/rc.d/rc.S# Script to run when going single user (runlevel 1).
su:1S:wait:/etc/rc.d/rc.K# Script to run when going multi user.
rc:2345:wait:/etc/rc.d/rc.M# What to do at the “Three Finger Salute”.
ca::ctrlaltdel:/sbin/shutdown -t5 -r now# Runlevel 0 halts the system.
l0:0:wait:/etc/rc.d/rc.0# Runlevel 6 reboots the system.
l6:6:wait:/etc/rc.d/rc.6# What to do when power fails.
pf::powerfail:/sbin/genpowerfail start# If power is back, cancel the running shutdown.
pg::powerokwait:/sbin/genpowerfail stop# These are the standard console login getties in multiuser mode:
c1:1235:respawn:/sbin/agetty 38400 tty1 linux
c2:1235:respawn:/sbin/agetty 38400 tty2 linux
c3:1235:respawn:/sbin/agetty 38400 tty3 linux
c4:1235:respawn:/sbin/agetty 38400 tty4 linux
c5:1235:respawn:/sbin/agetty 38400 tty5 linux
c6:12345:respawn:/sbin/agetty 38400 tty6 linux# Local serial lines:
#s1:12345:respawn:/sbin/agetty -L ttyS0 9600 vt100
#s2:12345:respawn:/sbin/agetty -L ttyS1 9600 vt100# Dialup lines:
#d1:12345:respawn:/sbin/agetty -mt60 38400,19200,9600,2400,1200 ttyS0 vt100
#d2:12345:respawn:/sbin/agetty -mt60 38400,19200,9600,2400,1200 ttyS1 vt100# Runlevel 4 used to be for an X window only system, until we discovered
# that it throws init into a loop that keeps your load avg at least 1 all
# the time. Thus, there is now one getty opened on tty6. Hopefully no one
# will notice. ;^)
# It might not be bad to have one text console anyway, in case something
# happens to X.
x1:4:respawn:/etc/rc.d/rc.4# End of /etc/inittab
[/code]Jos da dodam,kada namestim runlevel 4 a ulogujem se kao root kwrite radi normalno….dok na useru ‘nebojsa’ nece.
[code]root@shadow:/home/nebojsa# kwrite /etc/inittab
No protocol specified
kwrite: cannot connect to X server :0.0
root@shadow:/home/nebojsa#
[/code]i jos nemam zvuka kad stavim na runlevel 4,prekrizen mi kmix skroz,probao sam da uradim alsaconfig ponovo al’ nece…dok na runlevel 3 radi sve normalno…Ovo mi se desavalo i na slack 12.1 !
Evo ja imam KDE 4.1.3 na Slacku, 12.1 doduše. Instalacija je prosta, programi rade svi, tu je i skoro najnoviji Amarok 1.9.8, K3B je prebačen na KDE4, kao i velika većina drugih programa. Pratio sam zvanično uputstvo sa Slackware sajta, i odande sam skidao pakete.
Hajde stavi link ,da ne trazim po sajtu uputvo !!!
Jel si skinuo pakete sa http://packages.slackware.it/ ili ?A zašto ne prebaciš runlevel na 4, omogućiš autologin iz Control Centra i uživaš?
Stavio bi ja na runlevel 4,ali onda mi ne radi kwrite,tj. ne mogu da otvaram fajlove sa njim,dok sa runlevel 3 mogu…
To je jedini razlog…Otvorio sam sa visudo i dodao sebe kao usera
[code]
# Host alias specification# User alias specification
# Cmnd alias specification
# Defaults specification
# Runas alias specification
# User privilege specification
root ALL=(ALL) ALL# Uncomment to allow people in group wheel to run all commands
# %wheel ALL=(ALL) ALL
# Same thing without a password
# %wheel ALL=(ALL) NOPASSWD: ALL# Samples
# %users ALL=/sbin/mount /cdrom,/sbin/umount /cdrom
# %users localhost=/sbin/shutdown -h now
# nebojsa ALL=(ALL) NOPASSWD: /sbin/shutdown, /sbin/reboot
29,1 Command
[/code]
Takodje sam u kwrite napravio skripte ove gore,ali ne funkcionisu…da li treba da uradim jos nesto ???
