Problem sa Slackware 10.2,nvidia

[arm]

Pre nego što iznesem svoj problem, pozdrav svim korisnicima Slackware linuxa!
Problem se tiče (za sada) podešavanje drajvera za nvidia 5200 grafičku karticu za Slackware 10.2!?
(prešap sam ovaj forum i nisam našao rešenje za problem pa sam rešio da pitam da li neko je neko imao sličan problem i kako da ga rešim!
Problem je sledeći:
Drajver skinut sa nvidiinog sajta “NVIDIA-Linux-x86-1.0-7676-pkg1.run” , kompajliran,instaliran ,sve je prošlo bez greške!?koristim kernel 2.4.31 znači po defoltu!
ALI ?! xorg.conf mi neizgleda kao na Slackware 10.1 ? Posle instalacije nigde mi nepiše ni n od nvidie,ali kada dodam nv umesto vesa diže mi x, kada nv promenim u nvidia podigne logo nvidia i prsne X vrati me u konzolu ili se na ekranu pojave boje kao velika slova ali toliko krupne da se ne raznazaju!
modules.conf je prauan fajl!
Šaljem xorg.conf:
—————————————————–
# File generated by xf86config.

#
# Copyright (c) 1999 by The XFree86 Project, Inc.
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the “Software”),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
# THE XFREE86 PROJECT BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of the XFree86 Project shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from the
# XFree86 Project.
#

# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of
# this file.
# **********************************************************************

# NOTE: This is a NEW IMPROVED version of XF86Config-fbdev that uses the vesa
# driver instead of the fbdev driver. Thanks to Kenneth Fanyo who pointed
# this out to me. 🙂

# This XF86Config file is designed for use with the VESA framebuffer.
# This generic interface should work with nearly all video cards
# (although not every card will support every resolution).

# With the new driver, it should no longer be required to have frame buffer
# support in the kernel, or to run it on the console.
#
# Enjoy! 🙂
# — [email protected]
#

# **********************************************************************
# Module section — this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section “Module”

# This loads the DBE extension module.

Load “dbe” # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection “extmod”
Option “omit xfree86-dga” # don’t initialise the DGA extension
EndSubSection

# This loads the font modules
Load “type1”
Load “freetype”
#Load “speedo”

# This loads the GLX module
Load “glx”

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section “Files”

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like “.txt” or “.db”). There is normally
# no need to change the default.

RgbPath “/usr/X11R6/lib/X11/rgb”

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don’t have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

FontPath “/usr/X11R6/lib/X11/fonts/local/”
FontPath “/usr/X11R6/lib/X11/fonts/misc/”
FontPath “/usr/X11R6/lib/X11/fonts/75dpi/:unscaled”
FontPath “/usr/X11R6/lib/X11/fonts/100dpi/:unscaled”
#FontPath “/usr/X11R6/lib/X11/fonts/Type1/”
FontPath “/usr/X11R6/lib/X11/fonts/CID/”
FontPath “/usr/X11R6/lib/X11/fonts/Speedo/”
FontPath “/usr/X11R6/lib/X11/fonts/75dpi/”
FontPath “/usr/X11R6/lib/X11/fonts/100dpi/”
FontPath “/usr/X11R6/lib/X11/fonts/cyrillic/”

# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.

# ModulePath “/usr/X11R6/lib/modules”

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section “ServerFlags”

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option “NoTrapSignals”

# Uncomment this to disable the VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.

# Option “DontVTSwitch”

# Uncomment this to disable the server abort sequence
# This allows clients to receive this key event.

# Option “DontZap”

# Uncomment this to disable the / mode switching
# sequences. This allows clients to receive these key events.

# Option “DontZoom”

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option “DisableVidModeExtension”

# Uncomment this to enable the use of a non-local xvidtune client.

# Option “AllowNonLocalXvidtune”

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option “DisableModInDev”

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option “AllowNonLocalModInDev”

# Set the basic blanking screen saver timeout.

# Option “blank time” “10” # 10 minutes

# Set the DPMS timeouts. These are set here because they are global
# rather than screen-specific. These settings alone don’t enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.

# Option “standby time” “20”
# Option “suspend time” “30”
# Option “off time” “60”

# On some platform the server needs to estimate the sizes of PCI
# memory and pio ranges. This is done by assuming that PCI ranges
# don’t overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.

# Option “EstimateSizesAggresively” “0”

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard’s InputDevice section
# **********************************************************************

Section “InputDevice”

Identifier “Keyboard1”
Driver “kbd”
# For most OSs the protocol can be omitted (it defaults to “Standard”).
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option “Protocol” “Xqueue”

# Set the keyboard auto repeat parameters. Not all platforms implement
# this.

# Option “AutoRepeat” “500 5”

# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1)).

# Option “Xleds” “1 2 3”

# To disable the XKEYBOARD extension, uncomment XkbDisable.

# Option “XkbDisable”

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a European
# keyboard, you will probably want to use one of:
#
# Option “XkbModel” “pc102”
# Option “XkbModel”
“pc105”
#
# If you have a Microsoft Natural keyboard, you can use:
#
# Option “XkbModel” “microsoft”
#
# If you have a US “windows” keyboard you will want:
#
# Option “XkbModel” “pc104”
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#
# Option “XkbLayout” “de”
#
# or:
#
# Option “XkbLayout” “de”
# Option “XkbVariant” “nodeadkeys”
#
# If you’d like to switch the positions of your capslock and
# control keys, use:
#
# Option “XkbOptions” “ctrl:swapcaps”

# These are the default XKB settings for X.Org
#
# Option “XkbRules” “xorg”
# Option “XkbModel” “pc101”
# Option “XkbLayout” “us”
# Option “XkbVariant” “”
# Option “XkbOptions” “”

EndSection

# **********************************************************************
# Core Pointer’s InputDevice section
# **********************************************************************

Section “InputDevice”

# Identifier and driver

Identifier “Mouse1”
Driver “mouse”
Option “Protocol” “ImPS/2”
Option “ZAxisMapping” “4 5”
Option “Device” “/dev/mouse”

# On platforms where PnP mouse detection is supported the following
# protocol setting can be used when using a newer PnP mouse:

# Option “Protocol” “Auto”

# The available mouse protocols types that you can set below are:
# Auto BusMouse GlidePoint GlidePointPS/2 IntelliMouse IMPS/2
# Logitech Microsoft MMHitTab MMSeries Mouseman MouseManPlusPS/2
# MouseSystems NetMousePS/2 NetScrollPS/2 OSMouse PS/2 SysMouse
# ThinkingMouse ThinkingMousePS/2 Xqueue
Option “Protocol” “PS/2”

# The mouse device. The device is normally set to /dev/mouse,
# which is usually a symbolic link to the real device.

Option “Device” “/dev/mouse”
# Option “Device” “/dev/psaux”
# Option “Device” “/dev/ttyS0”
# Option “Device” “/dev/ttyS1”

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option “Protocol” “Xqueue”

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option “BaudRate” “9600”
# Option “SampleRate” “150”

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option “Emulate3Buttons”
# Option “Emulate3Timeout” “50”

# ChordMiddle is an option for some 3-button Logitech mice

# Option “ChordMiddle”

EndSection

# Some examples of extended input devices

# Section “InputDevice”
# Identifier “spaceball”
# Driver “magellan”
# Option “Device” “/dev/cua0”
# EndSection
#
# Section “InputDevice”
# Identifier “spaceball2”
# Driver “spaceorb”
# Option “Device” “/dev/cua0”
# EndSection
#
# Section “InputDevice”
# Identifier “touchscreen0”
# Driver “microtouch”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “1412”
# Option “MaxX” “15184”
# Option “MinY” “15372”
# Option “MaxY” “1230”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection
#
# Section “InputDevice”
# Identifier “touchscreen1”
# Driver “elo2300”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “231”
# Option “MaxX” “3868”
# Option “MinY” “3858”
# Option “MaxY” “272”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonThreshold” “17”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section “Monitor”

Identifier “My Monitor”

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR’S
# USER MANUAL FOR THE CORRECT NUMBERS.

HorizSync 30-71

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR’S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 50-160

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

Section “Device”
Identifier “VESA Framebuffer”
Driver “nv”
#VideoRam 128000
# Insert Clocks lines here if appropriate
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the “-screen”
# option.
Section “Screen”
Identifier “Screen 1”
Device “VESA Framebuffer”
Monitor “My Monitor”

# If your card can handle it, a higher default color depth (like 24 or 32)
# is highly recommended.

# DefaultDepth 8
# DefaultDepth 16
DefaultDepth 24
# DefaultDepth 32

# “1024×768” is also a conservative usable default resolution. If you
# have a better monitor, feel free to try resolutions such as
# “1152×864”, “1280×1024”, “1600×1200”, and “1800×1400” (or whatever your
# card/monitor can produce)

Subsection “Display”
Depth 8
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 16
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 24
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 32
Modes “1024×768” “800×600” “640×480”
EndSubsection

EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# “-layout” option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section “ServerLayout”

# The Identifier line must be present
Identifier “Simple Layout”

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.

Screen “Screen 1”

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include “CorePointer”, “CoreKeyboard” and
# “SendCoreEvents”.

InputDevice “Mouse1” “CorePointer”
InputDevice “Keyboard1” “CoreKeyboard”

EndSection
—————————————————————————————–
Ako neko ima rešenje bio bi mu zahvalan, sada koristim x bez 3d akceleracije kao što vidite iz xorg.conf fajla!

[djux]

Da li si kao root odradio X -configure? Ako jesi u root direktorijumu imas xorg.conf.new koji potom treba da kopiras u /etc/X11/ kao xorg.conf

[arm]

Da li si kao root odradio X -configure? Ako jesi u root direktorijumu imas xorg.conf.new koji potom treba da kopiras u /etc/X11/ kao xorg.conf

Probao ali ništa,sve isto kao i pre!

[arm]

jel moguće da nema nikog ko zna odgovor na ovo moje pitnje?
ako ga skoro ne reĹĄim,prelazim na DEBIAN 3.1,tamo sve radi lepo ali ne i brĹže!?

[japan]

probaj sa nekom drugom verzijom drajvera

[arm]

Sećam se na ovom forumu nekada kada je”radio” bilo je dovoljno postaviti problem i on bi za sat dva bio rešen! bilo je to pre 2 godine i jače a sada novi ljudi novi forum,nemislim da vređam nikog ovo je samo konstatacija!

[arm]

isti problem kao moj
http://www.nvnews.net/vbulletin/showthread.php?t=60179

[LimitMan]

U redu je da stavis nvidia (umesto nv) … u ostalom, conf ti je dobar … Ali moras da vidis sta te muci …

Kada ti se pojave ta velika slova koja ne mozes da procitas, rebootuj masinu (nadam se da si stavio default init 3) i udji u konzolu … Zatim pogledaj (iz nekog text editora) file /var/log/Xorg.0.log. Ukoliko je file prazan onda je logrotate odradeo svoje i onda pogldaj /var/log/Xorg.1.log
Nadji deo koji kaze:

(==) Using config file:

uveri se da ispod tog dela pise:

(II) LoadModule: “nvidia”
A ne vesa ili nv

Alinije koje ispisuje driver trebalo bi da pocnu sa:

(II) NVIDIA(0)

Tu mozes da lociras problem (tu su negde ona VELIKA slova, ali ovog puta smanjena) … Ukoliko ne umes da protumacis iskopiraj mi taj deo koji ide ispod (II) NVIDIA(0) …

[LimitMan]

Sećam se na ovom forumu nekada kada je”radio” bilo je dovoljno postaviti problem i on bi za sat dva bio rešen! bilo je to pre 2 godine i jače a sada novi ljudi novi forum,nemislim da vređam nikog ovo je samo konstatacija!

I sad se desava .. Ali kada ima ljudi koji znaju da ti pomognu ili su voljni da ti pomognu online … 😀

[arm]

[quote=”arm”]Sećam se na ovom forumu nekada kada je”radio” bilo je dovoljno postaviti problem i on bi za sat dva bio rešen! bilo je to pre 2 godine i jače a sada novi ljudi novi forum,nemislim da vređam nikog ovo je samo konstatacija!

I sad se desava .. Ali kada ima ljudi koji znaju da ti pomognu ili su voljni da ti pomognu online … :D[/quote]
Upravu si 100%! Samo što su ljudi bili “pre” voljniji da pruže pomoć nego sada!? A ja sam na ovom forumu skoro od osnivanja,zbog tog iznosim samo činjenice 😀 .
(==) Log file: “/var/log/Xorg.0.log”, Time: Sat Nov 26 19:49:41 2005
(==) Using config file: “/etc/X11/xorg.conf”
(==) ServerLayout “Simple Layout”
(**) |–>Screen “Screen 1” (0)
(**) | |–>Monitor “My Monitor”
(**) | |–>Device “NV34”
(**) |–>Input Device “Mouse1”
(**) |–>Input Device “Keyboard1”
(WW) `fonts.dir’ not found (or not valid) in “/usr/X11R6/lib/X11/fonts/local/”.
Entry deleted from font path.
(Run ‘mkfontdir’ on “/usr/X11R6/lib/X11/fonts/local/”).
(**) FontPath set to “/usr/X11R6/lib/X11/fonts/TTF/,/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/CID/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/,/usr/X11R6/lib/X11/fonts/cyrillic/”
(**) RgbPath set to “/usr/X11R6/lib/X11/rgb”
(**) ModulePath set to “/usr/X11R6/lib/modules”
(WW) Open APM failed (/dev/apm_bios) (No such device)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.7
X.Org XInput driver : 0.4
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: “bitmap”
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: “pcidata”
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(–) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,0305 card 0000,0000 rev 03 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,8305 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:07:0: chip 1106,0686 card 1106,0000 rev 40 class 06,01,00 hdr 80
(II) PCI: 00:07:1: chip 1106,0571 card 0000,0000 rev 06 class 01,01,8a hdr 00
(II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 1a class 0c,03,00 hdr 00
(II) PCI: 00:07:3: chip 1106,3038 card 0925,1234 rev 1a class 0c,03,00 hdr 00
(II) PCI: 00:07:4: chip 1106,3057 card 0000,0000 rev 40 class 06,80,00 hdr 00
(II) PCI: 00:0f:0: chip 109e,036e card 0000,0000 rev 11 class 04,00,00 hdr 80
(II) PCI: 00:0f:1: chip 109e,0878 card 0000,0000 rev 11 class 04,80,00 hdr 80
(II) PCI: 00:10:0: chip 14f1,1033 card 13e0,02b0 rev 08 class 07,80,00 hdr 00
(II) PCI: 00:11:0: chip 13f6,0111 card 13f6,0111 rev 10 class 04,01,00 hdr 00
(II) PCI: 01:00:0: chip 10de,0322 card 0000,0000 rev a1 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 – 0x0000ffff (0x10000) IX
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 – 0xffffffff (0x0) MX
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 – 0xffffffff (0x0) MX
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xe0000000 – 0xe1ffffff (0x2000000) MX
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xd8000000 – 0xdfffffff (0x8000000) MX
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(–) PCI: (0:15:0) Brooktree Corporation Bt878 Video Capture rev 17, Mem @ 0xe2011000/12
(–) PCI:*(1:0:0) nVidia Corporation NV34 [GeForce FX 5200] rev 161, Mem @ 0xe0000000/24, 0xd8000000/27
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 – 0xffffffff (0x0) MX
[1] -1 0 0x00000000 – 0x0000ffff (0x10000) IX
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 – 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 – 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 – 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 – 0x000effff (0x30000) MX
[4] -1 0 0x00000000 – 0x0009ffff (0xa0000) MX
[5] -1 0 0x0000ffff – 0x0000ffff (0x1) IX
[6] -1 0 0x00000000 – 0x000000ff (0x100) IX
(II) PCI Memory resource overlap reduced 0xd0000000 from 0xd7ffffff to 0xcfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xe2000000 – 0xe200ffff (0x10000) MX
[1] -1 0 0xe2010000 – 0xe2010fff (0x1000) MX
[2] -1 0 0xd0000000 – 0xcfffffff (0x0) MXO
[3] -1 0 0xd8000000 – 0xdfffffff (0x8000000) MX(B)
[4] -1 0 0xe0000000 – 0xe0ffffff (0x1000000) MX(B)
[5] -1 0 0xe2011000 – 0xe2011fff (0x1000) MX(B)
[6] -1 0 0x0000e000 – 0x0000e0ff (0x100) IX
[7] -1 0 0x0000dc00 – 0x0000dc07 (0x8) IX
[8] -1 0 0x0000c800 – 0x0000c81f (0x20) IX
[9] -1 0 0x0000c400 – 0x0000c41f (0x20) IX
[10] -1 0 0x0000c000 – 0x0000c00f (0x10) IX
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xe2000000 – 0xe200ffff (0x10000) MX
[1] -1 0 0xe2010000 – 0xe2010fff (0x1000) MX
[2] -1 0 0xd0000000 – 0xcfffffff (0x0) MXO
[3] -1 0 0xd8000000 – 0xdfffffff (0x8000000) MX(B)
[4] -1 0 0xe0000000 – 0xe0ffffff (0x1000000) MX(B)
[5] -1 0 0xe2011000 – 0xe2011fff (0x1000) MX(B)
[6] -1 0 0x0000e000 – 0x0000e0ff (0x100) IX
[7] -1 0 0x0000dc00 – 0x0000dc07 (0x8) IX
[8] -1 0 0x0000c800 – 0x0000c81f (0x20) IX
[9] -1 0 0x0000c400 – 0x0000c41f (0x20) IX
[10] -1 0 0x0000c000 – 0x0000c00f (0x10) IX
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 – 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 – 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 – 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 – 0x000effff (0x30000) MX
[4] -1 0 0x00000000 – 0x0009ffff (0xa0000) MX
[5] -1 0 0x0000ffff – 0x0000ffff (0x1) IX
[6] -1 0 0x00000000 – 0x000000ff (0x100) IX
(II) All system resource ranges:
[0] -1 0 0xffe00000 – 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 – 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 – 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 – 0x000effff (0x30000) MX
[4] -1 0 0x00000000 – 0x0009ffff (0xa0000) MX
[5] -1 0 0xe2000000 – 0xe200ffff (0x10000) MX
[6] -1 0 0xe2010000 – 0xe2010fff (0x1000) MX
[7] -1 0 0xd0000000 – 0xcfffffff (0x0) MXO
[8] -1 0 0xd8000000 – 0xdfffffff (0x8000000) MX(B)
[9] -1 0 0xe0000000 – 0xe0ffffff (0x1000000) MX(B)
[10] -1 0 0xe2011000 – 0xe2011fff (0x1000) MX(B)
[11] -1 0 0x0000ffff – 0x0000ffff (0x1) IX
[12] -1 0 0x00000000 – 0x000000ff (0x100) IX
[13] -1 0 0x0000e000 – 0x0000e0ff (0x100) IX
[14] -1 0 0x0000dc00 – 0x0000dc07 (0x8) IX
[15] -1 0 0x0000c800 – 0x0000c81f (0x20) IX
[16] -1 0 0x0000c400 – 0x0000c41f (0x20) IX
[17] -1 0 0x0000c000 – 0x0000c00f (0x10) IX
(II) LoadModule: “dbe”
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: “extmod”
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: “type1″
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: “freetype”
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor=”X.Org Foundation & the After X-TT Project”
compiled for 6.8.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: “glx”
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.so
(II) Module glx: vendor=”NVIDIA Corporation”
compiled for 4.0.2, module version = 1.0.7676
Module class: XFree86 Server Extension
ABI class: XFree86 Server Extension, version
0.1
(II) Loading extension GLX
(II) LoadModule: “dri”
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module “drm”
(II) LoadModule: “drm”
(II) Loading /usr/X11R6/lib/modules/linux/libdrm.a
(II) Module drm: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension XFree86-DRI
(II) LoadModule: “nvidia”
(II) Loading /usr/X11R6/lib/modules/drivers/nvidia_drv.o
(II) Module nvidia: vendor=”NVIDIA Corporation”
compiled for 4.0.2, module version = 1.0.7676
Module class: XFree86 Video Driver
(II) LoadModule: “mouse”
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) LoadModule: “kbd”
(II) Loading /usr/X11R6/lib/modules/input/kbd_drv.o
(II) Module kbd: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) NVIDIA X Driver 1.0-7676 Fri Jul 29 13:01:02 PDT 2005
(II) NVIDIA Unified Driver for all NVIDIA GPUs
(II) Primary Device is: PCI 01:00:0
(–) Assigning device section with no busID to primary device
(–) Chipset NVIDIA GPU found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 – 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 – 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 – 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 – 0x000effff (0x30000) MX
[4] -1 0 0x00000000 – 0x0009ffff (0xa0000) MX
[5] -1 0 0xe2000000 – 0xe200ffff (0x10000) MX
[6] -1 0 0xe2010000 – 0xe2010fff (0x1000) MX
[7] -1 0 0xd0000000 – 0xcfffffff (0x0) MXO
[8] -1 0 0xd8000000 – 0xdfffffff (0x8000000) MX(B)
[9] -1 0 0xe0000000 – 0xe0ffffff (0x1000000) MX(B)
[10] -1 0 0xe2011000 – 0xe2011fff (0x1000) MX(B)
[11] -1 0 0x0000ffff – 0x0000ffff (0x1) IX
[12] -1 0 0x00000000 – 0x000000ff (0x100) IX
[13] -1 0 0x0000e000 – 0x0000e0ff (0x100) IX
[14] -1 0 0x0000dc00 – 0x0000dc07 (0x8) IX
[15] -1 0 0x0000c800 – 0x0000c81f (0x20) IX
[16] -1 0 0x0000c400 – 0x0000c41f (0x20) IX
[17] -1 0 0x0000c000 – 0x0000c00f (0x10) IX
(II) resource ranges after probing:
[0] -1 0 0xffe00000 – 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 – 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 – 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 – 0x000effff (0x30000) MX
[4] -1 0 0x00000000 – 0x0009ffff (0xa0000) MX
[5] -1 0 0xe2000000 – 0xe200ffff (0x10000) MX
[6] -1 0 0xe2010000 – 0xe2010fff (0x1000) MX
[7] -1 0 0xd0000000 – 0xcfffffff (0x0) MXO
[8] -1 0 0xd8000000 – 0xdfffffff (0x8000000) MX(B)
[9] -1 0 0xe0000000 – 0xe0ffffff (0x1000000) MX(B)
[10] -1 0 0xe2011000 – 0xe2011fff (0x1000) MX(B)
[11] 0 0 0x000a0000 – 0x000affff (0x10000) MS
[12] 0 0 0x000b0000 – 0x000b7fff (0x8000) MS
[13] 0 0 0x000b8000 – 0x000bffff (0x8000) MS
[14] -1 0 0x0000ffff – 0x0000ffff (0x1) IX
[15] -1 0 0x00000000 – 0x000000ff (0x100) IX
[16] -1 0 0x0000e000 – 0x0000e0ff (0x100) IX
[17] -1 0 0x0000dc00 – 0x0000dc07 (0x8) IX
[18] -1 0 0x0000c800 – 0x0000c81f (0x20) IX
[19] -1 0 0x0000c400 – 0x0000c41f (0x20) IX
[20] -1 0 0x0000c000 – 0x0000c00f (0x10) IX
[21] 0 0 0x000003b0 – 0x000003bb (0xc) IS
[22] 0 0 0x000003c0 – 0x000003df (0x20) IS
(II) Setting vga for screen 0.
(**) NVIDIA(0): Depth 24, (–) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(–) NVIDIA(0): Linear framebuffer at 0xD8000000
(–) NVIDIA(0): MMIO registers at 0xE0000000
(II) NVIDIA(0): NVIDIA GPU detected as: GeForce FX 5200
(–) NVIDIA(0): VideoBIOS: 04.34.20.69.00
(–) NVIDIA(0): Interlaced video modes are supported on this GPU
(II) NVIDIA(0): Detected AGP rate: 4X
(–) NVIDIA(0): VideoRAM: 131072 kBytes
(II) NVIDIA(0): Connected display device(s): CRT-0, TV-0
(WW) NVIDIA(0): Multiple displays connected, but only one display allowed;
(WW) NVIDIA(0): using first display
(–) NVIDIA(0): CRT-0: maximum pixel clock: 350 MHz
(II) Loading sub module “ddc”
(II) LoadModule: “ddc”
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module “int10”
(II) LoadModule: “int10″
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) NVIDIA(0): Primary V_BIOS segment is: 0xc000
(II) NVIDIA(0): My Monitor: Using hsync range of 30.00-69.00 kHz
(II) NVIDIA(0): My Monitor: Using vrefresh range of 50.00-160.00 Hz
(II) NVIDIA(0): Clock range: 12.00 to 350.00 MHz
(II) NVIDIA(0): Not using default mode “1280×960” (hsync out of range)
(II) NVIDIA(0): Not using default mode “640×480” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1280×1024” (hsync out of range)
(II) NVIDIA(0): Not using default mode “640×512” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1280×1024” (hsync out of range)
(II) NVIDIA(0): Not using default mode “640×512” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1600×1200” (hsync out of range)
(II) NVIDIA(0): Not using default mode “800×600” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1600×1200” (hsync out of range)
(II) NVIDIA(0): Not using default mode “800×600” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1600×1200” (hsync out of range)
(II) NVIDIA(0): Not using default mode “800×600” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1600×1200” (hsync out of range)
(II) NVIDIA(0): Not using default mode “800×600” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1600×1200” (hsync out of range)
(II) NVIDIA(0): Not using default mode “800×600” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1792×1344” (hsync out of range)
(II) NVIDIA(0): Not using default mode “896×672” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1792×1344” (hsync out of range)
(II) NVIDIA(0): Not using default mode “896×672” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1856×1392” (hsync out of range)
(II) NVIDIA(0): Not using default mode “928×696” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1856×1392” (hsync out of range)
(II) NVIDIA(0): Not using default mode “928×696” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1920×1440” (hsync out of range)
(II) NVIDIA(0): Not using default mode “960×720” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1920×1440” (hsync out of range)
(II) NVIDIA(0): Not using default mode “960×720” (hsync out of range)
(WW) (1400×1050,My Monitor) mode clock 122MHz exceeds DDC maximum 110MHz
(II) NVIDIA(0): Not using default mode “1400×1050” (hsync out of range)
(II) NVIDIA(0): Not using default mode “700×525” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1920×1440” (hsync out of range)
(II) NVIDIA(0): Not using default mode “960×720” (hsync out of range)
(II) NVIDIA(0): Not using default mode “2048×1536” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1024×768” (hsync out of range)
(II) NVIDIA(0): Not using default mode “2048×1536” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1024×768” (hsync out of range)
(II) NVIDIA(0): Not using default mode “2048×1536” (bad mode clock/interlace/doublescan)
(II) NVIDIA(0): Not using default mode “1024×768” (hsync out of range)
(II) NVIDIA(0): Not using default mode “1400×1050” (width too large for virtual size)
(II) NVIDIA(0): Not using default mode “1280×1024” (width too large for virtual size)
(II) NVIDIA(0): Not using default mode “1280×960” (width too large for virtual size)
(II) NVIDIA(0): Not using default mode “1152×864” (width too large for virtual size)
(II) NVIDIA(0): Not using default mode “1152×768” (width too large for virtual size)
(WW) NVIDIA(0): Not using mode “700×525” (height 1050 is larger than
(WW) NVIDIA(0): EDID-specified maximum 1024)
(WW) NVIDIA(0): Not using mode “576×384”:
(WW) NVIDIA(0): horizontal sync start (589) not a multiple of 8
(WW) NVIDIA(0): Not using mode “360×200”:
(WW) NVIDIA(0): horizontal sync start (378) not a multiple of 8
(**) NVIDIA(0): Validated modes for display device CRT-0:
(**) NVIDIA(0): Default mode “1024×768”: 94.5 MHz, 68.7 kHz, 85.0 Hz
(**) NVIDIA(0): Default mode “800×600”: 56.3 MHz, 53.7 kHz, 85.1 Hz
(**) NVIDIA(0): Default mode “1024×768”: 78.8 MHz, 60.1 kHz, 75.1 Hz
(**) NVIDIA(0): Default mode “1024×768”: 75.0 MHz, 56.5 kHz, 70.1 Hz
(**) NVIDIA(0): Default mode “1024×768”: 65.0 MHz, 48.4 kHz, 60.0 Hz
(**) NVIDIA(0): Default mode “1024×768”: 44.9 MHz, 35.5 kHz, 87.0 Hz (I)
(**) NVIDIA(0): Default mode “832×624”: 57.3 MHz, 49.7 kHz, 74.6 Hz
(**) NVIDIA(0): Default mode “800×600”: 49.5 MHz, 46.9 kHz, 75.0 Hz
(**) NVIDIA(0): Default mode “800×600”: 50.0 MHz, 48.1 kHz, 72.2 Hz
(**) NVIDIA(0): Default
mode “800×600”: 40.0 MHz, 37.9 kHz, 60.3 Hz
(**) NVIDIA(0): Default mode “800×600”: 36.0 MHz, 35.2 kHz, 56.2 Hz
(**) NVIDIA(0): Default mode “640×512”: 54.0 MHz, 64.0 kHz, 60.0 Hz (D)
(**) NVIDIA(0): Default mode “640×480”: 36.0 MHz, 43.3 kHz, 85.0 Hz
(**) NVIDIA(0): Default mode “640×480”: 31.5 MHz, 37.5 kHz, 75.0 Hz
(**) NVIDIA(0): Default mode “640×480”: 31.5 MHz, 37.9 kHz, 72.8 Hz
(**) NVIDIA(0): Default mode “640×480”: 25.2 MHz, 31.5 kHz, 60.0 Hz
(**) NVIDIA(0): Default mode “640×480”: 54.0 MHz, 60.0 kHz, 60.0 Hz (D)
(**) NVIDIA(0): Default mode “720×400”: 35.5 MHz, 37.9 kHz, 85.0 Hz
(**) NVIDIA(0): Default mode “640×400”: 31.5 MHz, 37.9 kHz, 85.1 Hz
(**) NVIDIA(0): Default mode “576×432”: 54.0 MHz, 67.5 kHz, 75.0 Hz (D)
(**) NVIDIA(0): Default mode “640×350”: 31.5 MHz, 37.9 kHz, 85.1 Hz
(**) NVIDIA(0): Default mode “512×384”: 47.2 MHz, 68.7 kHz, 85.0 Hz (D)
(**) NVIDIA(0): Default mode “512×384”: 39.4 MHz, 60.1 kHz, 75.1 Hz (D)
(**) NVIDIA(0): Default mode “512×384”: 37.5 MHz, 56.5 kHz, 70.1 Hz (D)
(**) NVIDIA(0): Default mode “512×384”: 32.5 MHz, 48.4 kHz, 60.0 Hz (D)
(**) NVIDIA(0): Default mode “512×384”: 22.4 MHz, 35.5 kHz, 86.9 Hz (D)
(**) NVIDIA(0): Default mode “416×312”: 28.6 MHz, 49.7 kHz, 74.7 Hz (D)
(**) NVIDIA(0): Default mode “400×300”: 28.1 MHz, 53.7 kHz, 85.3 Hz (D)
(**) NVIDIA(0): Default mode “400×300”: 24.8 MHz, 46.9 kHz, 75.1 Hz (D)
(**) NVIDIA(0): Default mode “400×300”: 25.0 MHz, 48.1 kHz, 72.2 Hz (D)
(**) NVIDIA(0): Default mode “400×300”: 20.0 MHz, 37.9 kHz, 60.3 Hz (D)
(**) NVIDIA(0): Default mode “400×300”: 18.0 MHz, 35.2 kHz, 56.3 Hz (D)
(**) NVIDIA(0): Default mode “320×240”: 18.0 MHz, 43.3 kHz, 85.2 Hz (D)
(**) NVIDIA(0): Default mode “320×240”: 15.8 MHz, 37.5 kHz, 75.0 Hz (D)
(**) NVIDIA(0): Default mode “320×240”: 15.8 MHz, 37.9 kHz, 72.8 Hz (D)
(**) NVIDIA(0): Default mode “320×240”: 12.6 MHz, 31.5 kHz, 60.1 Hz (D)
(**) NVIDIA(0): Default mode “320×200”: 15.8 MHz, 37.9 kHz, 85.3 Hz (D)
(**) NVIDIA(0): Default mode “320×175”: 15.8 MHz, 37.9 kHz, 85.3 Hz (D)
(II) NVIDIA(0): Virtual screen size determined to be 1024 x 768
(–) NVIDIA(0): Display dimensions: (320, 240) mm
(–) NVIDIA(0): DPI set to (81, 81)
(II) Loading sub module “fb”
(II) LoadModule: “fb”
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module “ramdac”
(II) LoadModule: “ramdac”
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor=”X.Org Foundation”
compiled for 6.8.2, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.7
(–) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don’t.
(II) resource ranges after preInit:
[0] 0 0 0xd8000000 – 0xdfffffff (0x8000000) MX
[1] 0 0 0xe0000000 – 0xe0ffffff (0x1000000) MX
[2] -1 0 0xffe00000 – 0xffffffff (0x200000) MX(B)
[3] -1 0 0x00100000 – 0x3fffffff (0x3ff00000) MXE(B)
[4] -1 0 0x000f0000 – 0x000fffff (0x10000) MX
[5] -1 0 0x000c0000 – 0x000effff (0x30000) MX
[6] -1 0 0x00000000 – 0x0009ffff (0xa0000) MX
[7] -1 0 0xe2000000 – 0xe200ffff (0x10000) MX
[8] -1 0 0xe2010000 – 0xe2010fff (0x1000) MX
[9] -1 0 0xd0000000 – 0xcfffffff (0x0) MXO
[10] -1 0 0xd8000000 – 0xdfffffff (0x8000000) MX(B)
[11] -1 0 0xe0000000 – 0xe0ffffff (0x1000000) MX(B)
[12] -1 0 0xe2011000 – 0xe2011fff (0x1000) MX(B)
[13] 0 0 0x000a0000 – 0x000affff (0x10000) MS(OprD)

[14] 0 0 0x000b0000 – 0x000b7fff (0x8000) MS(OprD)
[15] 0 0 0x000b8000 – 0x000bffff (0x8000) MS(OprD)
[16] -1 0 0x0000ffff – 0x0000ffff (0x1) IX
[17] -1 0 0x00000000 – 0x000000ff (0x100) IX
[18] -1 0 0x0000e000 – 0x0000e0ff (0x100) IX
[19] -1 0 0x0000dc00 – 0x0000dc07 (0x8) IX
[20] -1 0 0x0000c800 – 0x0000c81f (0x20) IX
[21] -1 0 0x0000c400 – 0x0000c41f (0x20) IX
[22] -1 0 0x0000c000 – 0x0000c00f (0x10) IX
[23] 0 0 0x000003b0 – 0x000003bb (0xc) IS(OprU)
[24] 0 0 0x000003c0 – 0x000003df (0x20) IS(OprU)
(II) NVIDIA(0): Setting mode “1024×768”
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(II) Loading extension NV-CONTROL
(==) RandR enabled
Symbol __glXgetActiveScreen from module /usr/X11R6/lib/modules/extensions/libdri.a is unresolved!
Symbol __glXgetActiveScreen from module /usr/X11R6/lib/modules/extensions/libdri.a is unresolved!
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing extension GLX

*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.

Fatal server error:
Caught signal 11. Server aborting

Please consult the The X.Org Foundation support
at http://wiki.X.Org
for help.
Please also check the log file at “/var/log/Xorg.0.log” for additional information.

mislim da je nešto oko fontova, pokušavao sam ali jok!

[Аутор]

Чланци