- This topic has 39 odgovora, 8 glasova, and was last updated 20 years, 2 months ranije by
.
-
Članci
-
2.4.31 …
Imao sam muka jer sam instalirao prema onom prvom linku pa nije radilo a onda sam neshto loopnuo iz onog drugog linka i proradilo …
Animaciju josh nisam namestio a i mrzi me to …I ovo sam uradio samo da bih tebi pomogao 😀
Uspeo sam da instaliram bootsplash na svom kernelu 2.4.29 i mogu vam reci da radi savrseno kao i animacija!
Pratio sam upustvo sa linka
http://www.madpenguin.org/cms/?m=show&id=626 koji je pronasao LimitMan, i koji pretpostavljam radi i na drugim 2.4xx kernelima.
Takodje sam koristio LimitMan-ov savet i stavio u lilo.conf vga=0x317Sve je teklo super i vredi truda ,medjutim , nakon prvog restarta, izasla mi je informacija :
Sound server informational message:
Error while initializing the sound driver:
device /dev/dsp can’t be opened (No such device)
The sound server will continue, using the null output device.Probao sam kmix – ne radi , alsamixer ispisuje :”function snd_ctl_open failed for default: No such device”
Probao sam alsaconf ali ispisuje poruku :
“no module by that name found”
i krece ALSA CONFIGURATOR prozor na kome pise :
“No Supported PnP or PCI Card Found”
“Would you like to probe legacy ISA Sound Cards/Chips”
Izaberem “Yes” kaze :
“No legacy drivers are available”
Sem ovog problema sa zvucnom imao sam i sa modemom ali posle ponovne instalacije drajvera,modem je proradio.
Izgleda mi da sam nesto zajebao sa zvucnom i njegovim drajverom.Sad neznam kako da vratim zvuk.Sta kazete sta moze da bude ?! 😆
Kahm …
O kojoj se zvucnoj radi? 😀
Ukoliko je integrisana na ploci i neznash koji je chip reci mi makar plochu …Poshto mi nisi rekao koja je ploca u pitanju (sem da je asusova a to je isto kao da si mi na pitanje koji pentium odgovorio “chetvorka” 😉 ) moram da te pusti da malo mlatish glavu
Morash opet da kompajlirash kernel 🙁
Na svu srecu, veci deo ti je kompajliran tako da ne morash da brigash!
idi znachi:
[code]
cd /usr/src/linux
make menuconfig
[/code]
idi do Sound, udji u podmeni, i na “Sound card support” stavi M (ne * ili
deselektovano)onda izadji iz configa (i naravno sacuvaj opcije)
pa cepaj
[code]
make dep
make
make modules
make modules_install
make bzImage
cp arch/i386/boot bzImage /boot/IMEKERNELA
[/code]ovde mozes i da prepises svoj stari kernel
pozovi lilo (naravno … ako si menjao ime kernela ubaci ga kao novu
stavku)
rebootuj komp…E sada na http://www.alsa-project.org/alsa-doc/ nadji uputstvo kako da instalirash svoju zvucnu … A ako budes dovoljno dobar i kazes mi koja je Asusova maticna ploca … onda cu da ti kazem i koja je tacno ploca i kako da instaliras 😀
btw …
Ako je stvarno Intelova zvucna kao shto kazhesh evo ti uputstva (i preporuchujem ti da uradish ono ./snddevices osim ako ne koristish devfs)
@LyB
Evo sta kaze lspci [-v]:00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] Sound Controller (rev a0)
Subsystem: Asustek Computer, Inc.: Unknown device 80b0
Flags: bus master, medium devsel, latency 32, IRQ 3
I/O ports at 9400
I/O ports at 9000
Capabilities: [48] Power Management version 2“Sound card support” mi je pod Modulom [M] tako da verovatno moram samo da instaliram driver kao sto sam morao na modemu.
Dali da to probam bez mukotrpnog MAKE-a?
Inace ploca mi je Asus P4S8X-X,i koliko se secam da je sound cipset bio intel8x0 ali moguce da gresim.
🙄Ti bash imash srece 😀
Taman sam poceo da kucam:
Ovaj … Nisam siguran ali mislim da gresis …
P4S8X-X !MISLIM! da ima ili cmi (c-media) ili realtekovu (sto mi je manje verovatno) zvucnu.
Ajde da to resimo ovako:
kad sam se setio da u torbici imam originalne drajvere za tvoju plocu ;-)))
Onda tamo u Drivers/Audio/C-Media/Linux/README kaze sledece:
Audio driver for CM8338/CM8738 chips by Chen-Li Tien
HARDWARE SUPPORTED
================================================================================
C-Media CMI8338
C-Media CMI8738
On-board C-Media chipsWHAT’S NEW
================================================================================1. Support modem interface for 8738. (select in kernel configuration)
2. Enable S/PDIF-in to S/PDIF-out (S/PDIF loop).
3. Enable 4 channels analog duplicate mode on 3 jack or 4 jack
configurateion.
4. Enable joystick support. (joystick driver needed)STEPS TO BUILD DRIVER
================================================================================1. Backup the Config.in and Makefile in the sound driver directory
(/usr/src/linux/driver/sound).
The Configure.help provide help when you config driver in step
4, please backup the original one (/usr/src/linux/Document) and
copy this file.
The cmpci is document for the driver in detail, please copy it
to /usr/src/linux/Document/sound so you can refer it. Backup if
there is already one.2. Extract the tar file by ‘tar xvzf cmpci-xx.tar.gz’ in the above
directory.3. Change directory to /usr/src/linux
4. Config cm8338 driver by ‘make menuconfig’, ‘make config’ or
‘make xconfig’ command.5. Please select Sound Card (CONFIG_SOUND=m) support and CMPCI
driver (CONFIG_SOUND_CMPCI=m) as modules. Resident mode not tested.
For driver option, please refer ‘DRIVER PARAMETER’6. Compile the kernel if necessary.
7. Compile the modules by ‘make modules’.
8. Install the modules by ‘make modules_install’
INSTALL DRIVER
================================================================================1. Before first time to run the driver, create module dependency by
‘depmod -a’2. To install the driver manually, enter ‘modprobe cmpci’.
3. Driver installation for various distributions:
a. Slackware 4.0
Add the ‘modprobe cmpci’ command in your /etc/rc.d/rc.modules
file.so you can start the driver automatically each time booting.b. Caldera OpenLinux 2.2
Use LISA to load the cmpci module.c. RedHat 6.0 and S.u.S.E. 6.1
Add following command in /etc/conf.modules:alias sound cmpci
also visit http://www.cmedia.com.tw for installation instruction.
DRIVER PARAMETER
================================================================================Some functions for the cm8738 can be configured in Kernel Configuration
or modules parameters. Set these parameters to 1 to enable.spdif_loop: Enable S/PDIF loop, this route S/PDIF-in to S/PDIF-out
directly.
four_ch: Enable 4 channels mode, rear-out or line-in will output
the same as line-out.
rear_out: Enable this if you have independent rear-out jacket on
your sound card, otherwise line-in will be used as
rear-out.
modem: You will need to set this parameter if you want to use
the HSP modem. You need install the pctel.o, the modem
driver itself.
joystich: Enable joystick. You will need to install Linux joystick
driver.I ubacen je jedan file blahlahxxx.tar.gz
Ne brini … Sve je ovo nepotrebno 😉Samo ti lepo obrati paznju na
HARDWARE SUPPORTED
================================================================================
C-Media CMI8338
C-Media CMI8738
On-board C-Media chipsI onda lepo idi na
http://www.alsa-project.org/alsa-doc/doc-php/template.php?company=C-Media&card=.&chip=CMI8338%2C+CMI8738&module=cmipciI prati detalje kao shto sam ti rekao ranije … 😀
Jedno 20 min posla 😉
Moraš biti prijavljen da bi postavio komentar u ovoj temi.