Ћирилица

[sanel_nbg22]

komandu xbindingkeys nemam a pokrenuo sam xorg conf i izabrao za graficku intel i810 i vise nemam onaj problem sa treperenjem .Isto tako mi sad radi i hotplug i sa lsusb je nasao logitech inc.
a ja mu nista nisam uradio 🙂 osim sto sam rekompajlirao kernel i ukljucio podrsku za HID 🙂

Zasto za protokol se koristi explorerps/2 ili imps/2 kad logitech ima protokol?

evo ako neko hoce da pogleda moj novi xorg.conf pa da mi kaze jel sam nesto zeznuo 🙂

[sanel_nbg22]

graficka intel on board chipset 852GME 64mb (shared)

[sanel_nbg22]

Evo ga moj xorg config. Inace monitor je 15” XGA TFT max rezolucija 1024×768 a graficka intel on board chipset 852GME 64mb (shared)

# **********************************************************************
# Module section — this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section “Module”

# This loads the DBE extension module.

Load “dbe” # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection “extmod”
Option “omit xfree86-dga” # don’t initialise the DGA extension
EndSubSection

# This loads the font modules
Load “type1”
Load “freetype”
#Load “speedo”

# This loads the GLX module
Load “glx”

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section “Files”

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like “.txt” or “.db”). There is normally
# no need to change the default.

RgbPath “/usr/X11R6/lib/X11/rgb”

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don’t have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.

# ModulePath “/usr/X11R6/lib/modules”

FontPath “/usr/X11R6/lib/X11/fonts/local”
FontPath “/usr/X11R6/lib/X11/fonts/misc”
FontPath “/usr/X11R6/lib/X11/fonts/75dpi:unscaled”
FontPath “/usr/X11R6/lib/X11/fonts/100dpi:unscaled”
FontPath “/usr/X11R6/lib/X11/fonts/Type1”
FontPath “/usr/X11R6/lib/X11/fonts/CID”
FontPath “/usr/X11R6/lib/X11/fonts/Speedo”
FontPath “/usr/X11R6/lib/X11/fonts/cyrillic”
FontPath “/usr/local/share/fonts”
EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section “ServerFlags”

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option “NoTrapSignals”

# Uncomment this to disable the VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.

# Option “DontVTSwitch”

# Uncomment this to disable the server abort sequence
# This allows clients to receive this key event.

# Option “DontZap”

# Uncomment this to disable the / mode switching
# sequences. This allows clients to receive these key events.

# Option “DontZoom”

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option “DisableVidModeExtension”

# Uncomment this to enable the use of a non-local xvidtune client.

# Option “AllowNonLocalXvidtune”

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option “DisableModInDev”

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option “AllowNonLocalModInDev”

# Set the basic blanking screen saver timeout.

# Option “blank time” “10” # 10 minutes

# Set the DPMS timeouts. These are set here because they are global
# rather than screen-specific. These settings alone don’t enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.

# Option “standby time” “20”
# Option “suspend time” “30”
# Option “off time” “60”

# On some platform the server needs to estimate the sizes of PCI
# memory and pio ranges. This is done by assuming that PCI ranges
# don’t overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.

# Option “EstimateSizesAggresively” “0”

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard’s InputDevice section
# **********************************************************************

Section “InputDevice”

Identifier “Keyboard1”
Driver “kbd”
# For most OSs the protocol can be omitted (it defaults to “Standard”).
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option “Protocol” “Xqueue”

# Set the keyboard auto repeat parameters. Not all platforms implement
# this.

# Option “AutoRepeat” “500 5”

# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1)).

# Option “Xleds” “1 2 3”

# To disable the XKEYBOARD extension, uncomment XkbDisable.

# Option “XkbDisable”

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a European
# keyboard, you will probably want to use one of:
#
# Option “XkbModel” “pc102”
# Option “XkbModel” “pc105”
#
# If you have a Microsoft Natural keyboard, you can use:
#
# Option “XkbModel” “microsoft”
#
# If you have a US “windows” keyboard you will want:
#
# Option “XkbModel” “pc104”
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#
# Option “XkbLayout” “de”
#
# or:
#
# Option “XkbLayout” “de”
# Option “XkbVariant” “nodeadkeys”
#
# If you’d like to switch the positions of your capslock and
# control keys, use:
#
# Option “XkbOptions” “ctrl:swapcaps”

# These are the default XKB settings for X.Org
#
# Option “XkbRules” “xorg”
# Option “XkbModel” “pc101”
# Option “XkbLayout” “us”
# Option “XkbVariant” “”
# Option “XkbOptions” “”

EndSection

# **********************************************************************
# Core Pointer’s InputDevice section
# **********************************************************************

Section “InputDevice”

# Identifier and driver

Identifier “Logitech MX700”
Driver “mouse”
Option “Protocol” “explorerps/2”
Option “Dev Name” “Logitech USB Receiver”
Option “Device” “/dev/mouse”
Option “Buttons” “8”
Option “ZAxisMapping” “4 5”

# On platforms where PnP mouse detection is supported the following
# protocol setting can be used when using a newer PnP mouse:

# Option “Protocol” “Auto”

# The available mouse protocols types that you can set below are:
# Auto BusMouse GlidePoint GlidePointPS/2 IntelliMouse IMPS/2
# Logitech Microsoft MMHitTab MMSeries Mouseman MouseManPlusPS/2
# MouseSystems NetMousePS/2 NetScrollPS/2 OSMouse PS/2 SysMouse
# ThinkingMouse ThinkingMousePS/2 Xqueue

# The mouse device. The device is normally set to /dev/mouse,
# which is usually a symbolic link to the real device.

# Option “Device” “/dev/psaux”
# Option “Device” “/dev/ttyS0”
# Option “Device” “/dev/ttyS1”

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option “Protocol” “Xqueue”

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option “BaudRate” “9600”
# Option “SampleRate” “150”

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option “Emulate3Buttons”
# Option “Emulate3Timeout” “50”

# ChordMiddle is an option for some 3-button Logitech mice

# Option “ChordMiddle”

EndSection

# Some examples of extended input devices

# Section “InputDevice”
# Identifier “spaceball”
# Driver “magellan”
# Option “Device” “/dev/cua0”
# EndSection
#
# Section “InputDevice”
# Identifier “spaceball2”
# Driver “spaceorb”
# Option “Device” “/dev/cua0”
#
EndSection
#
# Section “InputDevice”
# Identifier “touchscreen0”
# Driver “microtouch”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “1412”
# Option “MaxX” “15184”
# Option “MinY” “15372”
# Option “MaxY” “1230”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection
#
# Section “InputDevice”
# Identifier “touchscreen1”
# Driver “elo2300”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “231”
# Option “MaxX” “3868”
# Option “MinY” “3858”
# Option “MaxY” “272”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonThreshold” “17”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section “Monitor”

Identifier “My Monitor”

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR’S
# USER MANUAL FOR THE CORRECT NUMBERS.

HorizSync 31.5 – 50.0

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR’S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 60

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

Section “Device”
Identifier “VESA Framebuffer”
Driver “vesa”
#VideoRam 4096
# Insert Clocks lines here if appropriate
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the “-screen”
# option.
Section “Screen”
Identifier “Screen 1”
Device “VESA Framebuffer”
Monitor “My Monitor”

# If your card can handle it, a higher default color depth (like 24 or 32)
# is highly recommended.

# DefaultDepth 8
# DefaultDepth 16
DefaultDepth 24
# DefaultDepth 32

# “1024×768” is also a conservative usable default resolution. If you
# have a better monitor, feel free to try resolutions such as
# “1152×864”, “1280×1024”, “1600×1200”, and “1800×1400” (or whatever your
# card/monitor can produce)

Subsection “Display”
Depth 8
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 16
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 24
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 32
Modes “1024×768” “800×600” “640×480”
EndSubsection

EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# “-layout” option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section “ServerLayout”

# The Identifier line must be present
Identifier “Simple Layout”

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.

Screen “Screen 1”

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include “CorePointer”, “CoreKeyboard” and
# “SendCoreEvents”.

InputDevice “Logitech MX700” “CorePointer”
InputDevice “Keyboard1” “CoreKeyboard”

EndSection

P.S. Za tips and tricks i imwheel znam ali mi je nesto pravio probleme ne mogu da se setim zasto pa sam odustao od te opcije. Sta je taj xbind…. ?

Koji logovi vam trebaju?

[sanel_nbg22]

Uspeo je nekako da proradi. Kao DevName pronasao je Logitech USB Receiver sto i koristim jer je mis bezicni 🙂 e sad lsusb mi ne daje nista.

E da jel znas mozda (ja pretpostavljam da je xorg.conf ali… ) zasto mi kad restartujem x ili idem na log of user konzola mi treperi sva i ne mogu nista da procitam?

P.S. Kao ZAxisMapping stavio sam “4 5” i skrol mi radi ali kako da namestim tumb buttons da rade alt+left i alt+right kao i da mi ono jedno dugme radi double click umesto sto to radi scroll klick?

Mnogo trazim znam 🙂

[sanel_nbg22]

Uspeo je nekako da proradi. Kao DevName pronasao je Logitech USB Receiver sto i koristim jer je mis bezicni 🙂 e sad lsusb mi ne daje nista.

E da jel znas mozda (ja pretpostavljam da je xorg.conf ali… ) zasto mi kad restartujem x ili idem na log of user konzola mi treperi sva i ne mogu nista da procitam?

[sanel_nbg22]

A reci mi kako si podesio to sve za misa u xorg.conf. Ja se secam da je ranije bila komanda mouse ili tako nesto pa ti slack izbaci mouse config ali to sad nema. Kao sto rekoh kad mi je hotplug enablovan onda mi mis ne radi? Jel znas sto je to tako? Btw jel moze da mi radi usb stick ako je hotplug disaeblovan? Posto mi za mount /dev/sda1 prijavljuje unsupported block device ili tako nesto

P.C. Komanda se zove mouseconfig ali je ja nemam 🙂 a imao sam je prosli put kad sam instalirao linux 😀

[sanel_nbg22]

Evo ovo sam nasao u helpu ali iskren da budem nije mi bas jasno.

Logitech Support
Some Logitech USB mice support special features, such as switching to a higher resolution, or providing cordless status. If KDE was built with libusb support, then you will get an additional tab for each supported mouse that is plugged in.
The supported devices are:
Wheel Mouse Optical
MouseMan Traveler
MouseMan Dual Optical
MX310 Optical Mouse
MX510 Optical Mouse
MX300 Optical Mouse
MX500 Optical Mouse
iFeel Mouse
Mouse Receiver
Dual Receiver
Cordless Freedom Optical
Cordless Elite Duo
MX700 Optical Mouse
Cordless Optical Trackman
Cordless MX Duo Receiver
MX100 Laser Mouse
Receiver for Cordless Presenter
Not all devices support all capabilities (typically cordless devices do not provide resolution switching, and of course only cordless devices support cordless status reporting), so some parts of the tab will not be enabled for some mouse types.
If the mouse supports resolution switching, the Sensor Resolution radio button group will be enabled, and you can switch from 400 counts per inch to 800 counts per inch and back. If you use 800 counts per inch, the same physical movement of the mouse will cause a greater (roughly double) amount of motion of the cursor. This tends to be popular amongst gamers.
If the mouse supports cordless reporting, the Battery Level and RF Channel widgets will be enabled. You can only change the RF Channel if your mouse has two channel support.
Fixing permission problems on Logitech mice
Because of the way USB devices work, the code that accesses the current status on Logitech mice needs to be able to write to the mouse. This should be handled by your distribution, but if not, you may need to do some configuration yourself.
On a Linux system, you should use the hotplug system to change the ownership and permissions on the mouse entry in /proc/bus/usb. One way to do this is to create a short script (/etc/hotplug/usb/consoleUserPerms) that changes the ownership and permissions, as shown below:

#!/bin/bash
#
# /etc/hotplug/usb/consoleUserPerms
#
# Sets up newly plugged in USB device so that the user who owns
# the console according to pam_console can access it from user space
#
# Note that for this script to work, you’ll need all of the following:
# a) a line in the file /etc/hotplug/usb.usermap or another usermap file
# in /etc/hotplug/usb/ that corresponds to the device you are using.
# b) a setup using pam_console creates the respective lock files
# containing the name of the respective user. You can check for that
# by executing “echo `cat /var/{run,lock}/console.lock`” and
# verifying the appropriate user is mentioned somewhere there.
# c) a Linux kernel supporting hotplug and usbdevfs
# d) the hotplug package (http://linux-hotplug.sourceforge.net/)
#
# In the usermap file, the first field “usb module” should be named
# “consoleUserPerms” to invoke this script.
#

if [ “${ACTION}” = “add” ] && [ -f “${DEVICE}” ]
then
# New code, using lock files instead of copying /dev/console permissions
# This also works with non-kdm logins (e.g. on a virtual terminal)
# Idea and code from Nalin Dahyabhai
if [ -f /var/run/console.lock ]
then
CONSOLEOWNER=`cat /var/run/console.lock`
elif [ -f /var/lock/console.lock ]
then
CONSOLEOWNER=`cat /var/lock/console.lock`
else
CONSOLEOWNER=
fi
if [ -n “$CONSOLEOWNER” ]
then
chmod 0000 “${DEVICE}”
chown “$CONSOLEOWNER” “${DEVICE}”
chmod 0600 “${DEVICE}”
fi
fi

The usermap file that goes with this is /etc/hotplug/usb/logitechmouse.usermap, as shown below:

# script match_flags idVendor idProduct bcdDevice_lo bcdDevice_hi bDeviceClass bDeviceSubClass bDeviceProtocol bInterfaceClass bInterfaceSubClass bInterfaceProtocol driver_info
# Wheel Mouse Optical
consoleUserPerms 0x0003 0x046d 0xc00e 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MouseMan Traveler
consoleUserPerms 0x0003 0x046d 0xc00f 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MouseMan Dual Optical
consoleUserPerms 0x0003 0x046d 0xc012 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MX310 Optical Mouse
consoleUserPerms 0x0003 0x046d 0xc01b 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MX510 Optical Mouse
consoleUserPerms 0x0003 0x046d 0xc01d 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MX300 Optical Mouse
consoleUserPerms 0x0003 0x046d 0xc024 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MX500 Optical Mouse
consoleUserPerms 0x0003 0x046d 0xc025 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# iFeel Mouse
consoleUserPerms 0x0003 0x046d 0xc031 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# Mouse Receiver
consoleUserPerms 0x0003 0x046d 0xc501 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# Dual Receiver
consoleUserPerms 0x0003 0x046d 0xc502 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# Cordless Freedom Optical
consoleUserPerms 0x0003 0x046d 0xc504 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# Cordless Elite Duo
consoleUserPerms 0x0003 0x046d 0xc505 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MX700 Optical Mouse
consoleUserPerms 0x0003 0x046d 0xc506 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# Cordless Optical Trackman
consoleUserPerms 0x0003 0x046d 0xc508 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# Cordless MX Duo Receiver
consoleUserPerms 0x0003 0x046d 0xc50b 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# MX100 Laser Mouse
consoleUserPerms 0x0003 0x046d 0xc50e 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000
# Receiver for Cordless Presenter
consoleUserPerms 0x0003 0x046d 0xc702 0x0000 0xffff 0x00 0x00 0x00 0x00 0x00 0x00 0x00000000

That should be all that is needed on Linux – just copy the files into /etc/hotplug/usb/, and when the mouse is plugged in, the ownership and permissions should be changed so that the user at the console can access the mouse.

[sanel_nbg22]

A kad installiram source sa cd-a imam i headers. A kad sam skinuo 2.6.11 imam samo kernel. Moje pitanje (konfuzno kao po obicaju 🙂 ) je da li mi za svaku verziju kernela trebaju i headeri i sta jos ili to on sam po kompajliranju izgenerise? THX

[sanel_nbg22]

Ja nisam rekao da je ideja proverena nego sam pitao da li neko to i pored svega ovoga radi 🙂

[sanel_nbg22]

A ima veze menuconfig, xconfig ili config ?? Kakve i zbog cega

[Аутор]

Чланци