- This topic has 3 одговора, 2 гласа, and was last updated 20 years, 10 months раније by
.
-
Чланци
-
Mnogo dobar 56K ali KPPP test modem kaze da nemoze da mu pristupi,
a nemam ni /dev/ttyS2 gde bi se inace nalazio modem, doduse stoji na PNP a jumper za IRQ na 4, u W2k mi se prijavljuje na COM3 IRQ7
I/O range 03e8-03ef.
Probao sam i ISApnpDUMP ali on nikako da generise /etc/isapnp.conf, pa neznam ni kako izgleda, ima samo neki /etc/isapnp. e boga pitaj sta je u produzetku, inace mi kroz konzolu izlista sve sta ima na ISA.
O linuxconf-u da i negovorim nema nigde nijednog po W2k tipologiji potrebnog I/O Ranga a o IRQ7 da i negovorim.
Pa ako neko zna sta mi je ciniti da ovo plekce proradi….. 8)Uspeo sam nekako da generisem pomenuti isapnp.conf,
a u /dev imam nekakav modem koji je u stvari simbolicki link na /ttyS2
koji pa uopste i nepostoji.
Mojo pitanje glasi kako da mu dodam COM port, a ovde mije u clipbordu i isapnp.conf pa ako nekog zanima ili taj neko moze da mi pomogne neka ga edituje po svom misljenju ince u W2k za isa komponente stoji ovako:
Modem dakle: COM3 IRQ7 I/O range 03e8-03ef
Mrezna: IRQ10 I/O range 02d0-02dfPa koje voljan nek mi barem nznaci sha da radim
Doduse cackao sam nesto kod IRQ4 jer mi se njego I/O cinio odgovarajucim, ali kako sam ga izcackao boga pitaj.
Unapred hvala# $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $
# Release isapnptools-1.26
#
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of the output file format, see isapnp.conf(5)
#
# For latest information and FAQ on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE
#
# Trying port address 0273
# Board 1 has serial identifier a6 96 f8 c5 aa 90 30 72 56
# Board 2 has serial identifier 39 97 16 e0 17 94 50 6d 50# (DEBUG)
(READPORT 0x0273)
(ISOLATE CLEAR)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING# Card 1: (serial identifier a6 96 f8 c5 aa 90 30 72 56)
# Vendor Id USR3090, Serial Number 2532885930, checksum 0xA6.
# Version 1.0, Vendor version 0.0
# ANSI string –>U.S. Robotics 56K Voice INT3Com 3C509B EtherLink III<–
#
# Logical device id TCM5094
# Device supports I/O range check register
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x39
# Device supports vendor reserved register @ 0x3a
# Device supports vendor reserved register @ 0x3c
# Device supports vendor reserved register @ 0x3e
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed if required
# Don't forget to uncomment the activate (ACT Y) when happy(CONFIGURE TCM5094/2534858775 (LD 0
# Compatible device id PNP80f7
# IRQ 3, 5, 7, 9, 10, 11, 12 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0210
# Maximum IO base address 0x03e0
# IO base alignment 16 bytes
# Number of IO addresses required: 16
# (IO 0 (SIZE 16) (BASE 0x0210) (CHECK))
(NAME "TCM5094/2534858775[0]{3Com 3C509B EtherLink III}")
# (ACT Y)
))
# End tag… Checksum 0x00 (OK)# Returns all cards to the "Wait for Key" state
(WAITFORKEY)PS
STO JE DOBAR OVAJ COMMANDERov PLUGINProbaj sa setserial. Procitaj sta kaze man i probaj.
Na primer:
# setserial -g /dev/ttyS2
ili
# setserial /dev/ttyS2 −v autoconfigbi trebalo da pomogne.
Com 2 je ipak 2f8, a ne 2e8 kako je bilo u mom BIOS-u, sada skoro sve radi sto se tiche modema, ali:
Kroz ROOT nalog prodjem i kao konektujem se, mada nema govora o bilo kakvom protoku podataka.
Dok mi kroz USERA pppd daemon iznenadno i “neocekivano” crkava.
Sta jos da pogledam FireWall mi nije ni instaliran, /etc/resolf.conf ima upravo one adrese koje sam mu postavio za DNS ptt-a, a logujem se sa PAP/CHAP, doduse samo u pap-secrets imam postavku koja mi je postavljena. 😕
Мораш бити пријављен да би поставио коментар у овој теми.