- This topic has 13 odgovora, 9 glasova, and was last updated 13 years, 7 months ranije by
.
-
Članci
-
Uzeo sam na probu telenor “Koristi mesec dana besplatno” i dobio sam USB modem “XSPlugP3″.
Tehnicka podrska mi je rekla da Linux nije podrzan sa ovim modemom, sto naravno nije tacno.Evo kako sam ja to uradio na PCLinuxOS 2007:
Kada se prikljuci modem na USB port racunar ga prepozna kao USB flash disk.
Na disku se nalaze drajveri za Windows i Mac. Znaci neupotrebljivo za Linux.
Pritiskom na dugme modema, modem se inicijalizuje i Linux ga prepozna kao ttyACM0 uredjaj.
Sada treba podesiti wvdial. Napravio sam /etc/ppp/peers/wvdial.conf
#wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Stupid Mode = 1
Modem Type = Analog Modem
Baud = 9600
New PPPD = yes
Modem = /dev/ttyACM0
ISDN = 0
Phone = *99***1#
Username = telenor
Password = gprs[Dialer telenor3G]
Init1 = ATZ
Init2 = AT+COPS=0,0,”YU MOBTEL”,2
Init3 = ATE0V1&D2&C1S0=0+IFC=2,2
Init4 = AT+CSQ
Init5 = AT+CGDCONT=1,”IP”,”internet”;
Modem Type = USB Modem
ISDN = 0
Modem = /dev/ttyACM0
#Dial Command = ATDT
#Phone = *99***1#
#Username = telenor
#Password = gprs
Baud = 460800[Dialer telenorGPRS]
Init1 = ATZ
Init2 = AT+COPS=0,0,”YU MOBTEL”,0
Init3 = ATE0V1&D2&C1S0=0+IFC=2,2
Init4 = AT+CSQ
Init5 = AT+CGDCONT=1,”IP”,”internet”;
Modem Type = USB Modem
ISDN = 0
Modem = /dev/ttyACM0
#Dial Command = ATDT
#Phone = *99***1#
#Username = telenor
#Password = gprs
Baud = 460800Sada za 3G startujemo:
wvdial –config /etc/ppp/peers/wvdial.conf telenor3G[root@~]# wvdial –config /etc/ppp/peers/wvdial.conf telenor3G
–> WvDial: Internet dialer version 1.54.0
–> Cannot get information for serial port.
–> Initializing modem.
–> Sending: ATZ
OK
–> Sending: AT+COPS=0,0,”YU MOBTEL”,2
AT+COPS=0,0,”YU MOBTEL”,2
OK
–> Sending: ATE0V1&D2&C1S0=0+IFC=2,2
ATE0V1&D2&C1S0=0+IFC=2,2
OK
–> Sending: AT+CSQ
+CSQ: 20,99
OK
–> Sending: AT+CGDCONT=1,”IP”,”internet”;
OK
–> Modem initialized.
–> Sending: ATDT*99***1#
–> Waiting for carrier.
CONNECT
–> Carrier detected. Starting PPP immediately.
–> Starting pppd at Fri Oct 3 13:13:04 2008
–> pid of pppd: 21477
–> Using interface ppp0
–> pppd: Connect: ppp0 /dev/ttyACM0
–> pppd: CHAP authentication succeeded
–> pppd: Could not determine remote IP address: defaulting to 10.64.64.64
–> pppd: not replacing existing default route to eth0 [192.168.10.7]
–> local IP address 172.17.85.4
–> remote IP address 10.64.64.64
–> primary DNS address 10.11.12.13
–> secondary DNS address 10.11.12.14a za GPRS:
wvdial –config /etc/ppp/peers/wvdial.conf telenorGPRS[root@~]# wvdial –config /etc/ppp/peers/wvdial.conf telenorGPRS
–> WvDial: Internet dialer version 1.54.0
–> Cannot get information for serial port.
–> Initializing modem.
–> Sending: ATZ
OK
–> Sending: AT+COPS=0,0,”YU MOBTEL”,0
AT+COPS=0,0,”YU MOBTEL”,0
OK
–> Sending: ATE0V1&D2&C1S0=0+IFC=2,2
ATE0V1&D2&C1S0=0+IFC=2,2
OK
–> Sending: AT+CSQ
+CSQ: 30,99
OK
–> Sending: AT+CGDCONT=1,”IP”,”internet”;
OK
–> Modem initialized.
–> Sending: ATDT*99***1#
–> Waiting for carrier.
CONNECT
–> Carrier detected. Starting PPP immediately.
–> Starting pppd at Fri Oct 3 13:10:07 2008
–> pid of pppd: 21397
–> Using interface ppp0
–> pppd: Connect: ppp0 /dev/ttyACM0
–> pppd: CHAP authentication succeeded
–> pppd: Could not determine remote IP address: defaulting to 10.64.64.64
–> pppd: not replacing existing default route to eth0 [192.168.10.7]
–> local IP address 172.17.153.156
–> remote IP address 10.64.64.64
–> primary DNS address 10.11.12.13
–> secondary DNS address 10.11.12.14Dodatne AT komande za prebacivanje 3G/GPRS su:
Prebaci na UMTS
AT+COPS=0,0,”YU MOBTEL”,2
Prebaci na GPRS
AT+COPS=0,0,”YU MOBTEL”,0Korisna je i komanda AT+CSQ koja daje jacinu signala.
Objasnjenje za dodatne AT komande sam nasao na lokaciji:
http://www.shapeshifter.se/2008/04/30/list-of-at-commands/Verujem da je ovo primenljivo i na drugim Linux distribucijama.
Oni koji vise vole graficki interfejs, mogu lako da prilagode svoju aplikaciju (KPPP i slicno).U međuvremenu mi je dosla do ruku i MTS kartica, pa sam probao i sa njom.
Prepravio sam wvdial.conf da obuhvatim i MTS:# wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Stupid Mode = 1
Modem Type = Analog Modem
Baud = 9600
New PPPD = yes
Modem = /dev/ttyACM0
ISDN = 0[Dialer telenor3G]
Init1 = ATZ
Init2 = AT+COPS=0,0,”YU MOBTEL”,2
Init3 = ATE0V1&D2&C1S0=0+IFC=2,2
Init4 = AT+CSQ
Init5 = AT+CGDCONT=1,”IP”,”internet”;
Modem Type = USB Modem
ISDN = 0
Modem = /dev/ttyACM0
Dial Command = ATDT
Phone = *99***1#
Username = telenor
Password = gprs
Baud = 460800[Dialer telenorGPRS]
Init1 = ATZ
Init2 = AT+COPS=0,0,”YU MOBTEL”,0
Init3 = ATE0V1&D2&C1S0=0+IFC=2,2
Init4 = AT+CSQ
Init5 = AT+CGDCONT=1,”IP”,”internet”;
Modem Type = USB Modem
ISDN = 0
Modem = /dev/ttyACM0
Dial Command = ATDT
Phone = *99***1#
Username = telenor
Password = gprs
Baud = 460800[Dialer mts3G]
Init1 = ATZ
Init2 = AT+COPS=0,0,”YUG 03″,2
Init3 = ATE0V1&D2&C1S0=0+IFC=2,2
Init4 = AT+CSQ
Init5 = AT+CGDCONT=1,”IP”,”3gdata”;
Modem Type = USB Modem
ISDN = 0
Modem = /dev/ttyACM0
Dial Command = ATDT
Phone = *99***1#
Username = mts
Password = 064
Baud = 460800[Dialer mtsGPRS]
Init1 = ATZ
Init2 = AT+COPS=0,0,”YUG 03″,0
Init3 = ATE0V1&D2&C1S0=0+IFC=2,2
Init4 = AT+CSQ
Init5 = AT+CGDCONT=1,”IP”,”3gdata”;
Modem Type = USB Modem
ISDN = 0
Modem = /dev/ttyACM0
Dial Command = ATDT
Phone = *99***1#
Username = mts
Password = 064
Baud = 460800za Telenor je sada:
wvdial –config /etc/ppp/peers/wvdial.conf telenor3G
wvdial –config /etc/ppp/peers/wvdial.conf telenorGPRS
a za MTS:
wvdial –config /etc/ppp/peers/wvdial.conf mts3G
wvdial –config /etc/ppp/peers/wvdial.conf mtsGPRSUređaj je onaj isti koji sam dobio od Telenora “XSPlugP3”
Ja pokusavam da namestim onaj Telekomov ZTE MF622 USB 3G Modem, al’ uporno mi izbacuje:
[code]brankko@kk-eee:~$ sudo wvdial –config /etc/wvdial.conf mts3G
–> WvDial: Internet dialer version 1.60
–> Cannot get information for serial port.
–> Initializing modem.
–> Sending: ATZ
ATZ
OK
–> Sending: AT+COPS=0,0,”YUG 03″,2
AT+COPS=0,0,”YUG 03″,2
ERROR
–> Bad init string.
^CCaught signal 2: Attempting to exit gracefully…
–> Cannot get information for serial port.
–> Initializing modem.
–> Sending: ATZ
ATZ
OK
–> Sending: AT+COPS=0,0,”YUG 03″,2
AT+COPS=0,0,”YUG 03″,2
ERROR
–> Bad init string.
^C
brankko@kk-eee:~$ [/code]Ja pokusavam da namestim onaj Telekomov ZTE MF622 USB 3G Modem, al’ uporno mi izbacuje:
Nemam iskustva sa tim modemom, ali koliko vidim na netu (google je nas najbolji prijatelj) to je neki slican ili isti kao Huawei E219.
Evo ti neki linkovi:
“raspad sistema; mts 3g net, ZTE MF622 i Ubuntu 8.10; & i’m back …”
http://abakus.wordpress.com/2008/12/05/raspad-sistema-mts-3g-net-zte-mf622-i-ubuntu-810/http://en.wikipedia.org/wiki/Vodafone_Mobile_Connect_Card_driver_for_Linux
http://www.ubuntu-rs.org/forum/viewthread.php?tid=6918
i ovde je bilo nešto O0Uff Googlao sam celu noc i celo jutro… i probao sve moguce tutorijale (ukljucujuci i sve varijante istih) koje sam nasao na netu i bez uspeha… Na kraju ga sredim da se kao uspesno instalira i detektuje ga sistem i sve, ali kad krene da zove… kvrc… “Bad init string”
Probao sam i ovaj Vodafon-ov software (doduse ne znam da li je bas ova verzija, ali skinuh ga sa njihovog nekog developer sajta, al nije htelo…Ajd probacu sad ove odavde…
[quote=”BRANKKO”]
Ja pokusavam da namestim onaj Telekomov ZTE MF622 USB 3G Modem, al’ uporno mi izbacuje:Nemam iskustva sa tim modemom, ali koliko vidim na netu (google je nas najbolji prijatelj) to je neki slican ili isti kao Huawei E219.
Evo ti neki linkovi:
“raspad sistema; mts 3g net, ZTE MF622 i Ubuntu 8.10; & i’m back …”
http://abakus.wordpress.com/2008/12/05/raspad-sistema-mts-3g-net-zte-mf622-i-ubuntu-810/http://en.wikipedia.org/wiki/Vodafone_Mobile_Connect_Card_driver_for_Linux
https://forge.betavine.net/projects/vodafonemobilec/
[/quote]
Upravo sam nabacio ubuntu 9.10 na svoj desktop… i imam malih problema pri ospsobljavanju istog za rad… tj jedan, jedini problem… imam buđavi 3g net od Telekoma… sa modemom ZTE MF622…i kad hoću da instaliram ovaj vodafone mobile connect… on mi traži da skine još 27 dodatnih paketa… što opet ne mogu da uradim, jer jedini net koji imam je upravo 3g… Pokušao sam da skidam pakete zasebno(na laptopu, prebacivao na desktop) … što se opet završilo neuspešno, jer je skoro svaki od njih tražio neke druge pakete, a ovi opet neke treće, i tako u nedogled…i posle 3-4 sata guglanja sam konačno odustao…
Bio bih zahvalan na bilo kakvoj vrsti pomoći… kad sam n00b… 🙁
Moraš biti prijavljen da bi postavio komentar u ovoj temi.