kde 3.4, mx700i hotplug

[sanel_nbg22]

Evo ga moj xorg config. Inace monitor je 15” XGA TFT max rezolucija 1024×768 a graficka intel on board chipset 852GME 64mb (shared)

# **********************************************************************
# Module section — this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section “Module”

# This loads the DBE extension module.

Load “dbe” # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection “extmod”
Option “omit xfree86-dga” # don’t initialise the DGA extension
EndSubSection

# This loads the font modules
Load “type1”
Load “freetype”
#Load “speedo”

# This loads the GLX module
Load “glx”

EndSection

# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************

Section “Files”

# The location of the RGB database. Note, this is the name of the
# file minus the extension (like “.txt” or “.db”). There is normally
# no need to change the default.

RgbPath “/usr/X11R6/lib/X11/rgb”

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don’t have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#

# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.

# ModulePath “/usr/X11R6/lib/modules”

FontPath “/usr/X11R6/lib/X11/fonts/local”
FontPath “/usr/X11R6/lib/X11/fonts/misc”
FontPath “/usr/X11R6/lib/X11/fonts/75dpi:unscaled”
FontPath “/usr/X11R6/lib/X11/fonts/100dpi:unscaled”
FontPath “/usr/X11R6/lib/X11/fonts/Type1”
FontPath “/usr/X11R6/lib/X11/fonts/CID”
FontPath “/usr/X11R6/lib/X11/fonts/Speedo”
FontPath “/usr/X11R6/lib/X11/fonts/cyrillic”
FontPath “/usr/local/share/fonts”
EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section “ServerFlags”

# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

# Option “NoTrapSignals”

# Uncomment this to disable the VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.

# Option “DontVTSwitch”

# Uncomment this to disable the server abort sequence
# This allows clients to receive this key event.

# Option “DontZap”

# Uncomment this to disable the / mode switching
# sequences. This allows clients to receive these key events.

# Option “DontZoom”

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

# Option “DisableVidModeExtension”

# Uncomment this to enable the use of a non-local xvidtune client.

# Option “AllowNonLocalXvidtune”

# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.

# Option “DisableModInDev”

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).

# Option “AllowNonLocalModInDev”

# Set the basic blanking screen saver timeout.

# Option “blank time” “10” # 10 minutes

# Set the DPMS timeouts. These are set here because they are global
# rather than screen-specific. These settings alone don’t enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.

# Option “standby time” “20”
# Option “suspend time” “30”
# Option “off time” “60”

# On some platform the server needs to estimate the sizes of PCI
# memory and pio ranges. This is done by assuming that PCI ranges
# don’t overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.

# Option “EstimateSizesAggresively” “0”

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard’s InputDevice section
# **********************************************************************

Section “InputDevice”

Identifier “Keyboard1”
Driver “kbd”
# For most OSs the protocol can be omitted (it defaults to “Standard”).
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.

# Option “Protocol” “Xqueue”

# Set the keyboard auto repeat parameters. Not all platforms implement
# this.

# Option “AutoRepeat” “500 5”

# Specifiy which keyboard LEDs can be user-controlled (eg, with xset(1)).

# Option “Xleds” “1 2 3”

# To disable the XKEYBOARD extension, uncomment XkbDisable.

# Option “XkbDisable”

# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a European
# keyboard, you will probably want to use one of:
#
# Option “XkbModel” “pc102”
# Option “XkbModel” “pc105”
#
# If you have a Microsoft Natural keyboard, you can use:
#
# Option “XkbModel” “microsoft”
#
# If you have a US “windows” keyboard you will want:
#
# Option “XkbModel” “pc104”
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#
# Option “XkbLayout” “de”
#
# or:
#
# Option “XkbLayout” “de”
# Option “XkbVariant” “nodeadkeys”
#
# If you’d like to switch the positions of your capslock and
# control keys, use:
#
# Option “XkbOptions” “ctrl:swapcaps”

# These are the default XKB settings for X.Org
#
# Option “XkbRules” “xorg”
# Option “XkbModel” “pc101”
# Option “XkbLayout” “us”
# Option “XkbVariant” “”
# Option “XkbOptions” “”

EndSection

# **********************************************************************
# Core Pointer’s InputDevice section
# **********************************************************************

Section “InputDevice”

# Identifier and driver

Identifier “Logitech MX700”
Driver “mouse”
Option “Protocol” “explorerps/2”
Option “Dev Name” “Logitech USB Receiver”
Option “Device” “/dev/mouse”
Option “Buttons” “8”
Option “ZAxisMapping” “4 5”

# On platforms where PnP mouse detection is supported the following
# protocol setting can be used when using a newer PnP mouse:

# Option “Protocol” “Auto”

# The available mouse protocols types that you can set below are:
# Auto BusMouse GlidePoint GlidePointPS/2 IntelliMouse IMPS/2
# Logitech Microsoft MMHitTab MMSeries Mouseman MouseManPlusPS/2
# MouseSystems NetMousePS/2 NetScrollPS/2 OSMouse PS/2 SysMouse
# ThinkingMouse ThinkingMousePS/2 Xqueue

# The mouse device. The device is normally set to /dev/mouse,
# which is usually a symbolic link to the real device.

# Option “Device” “/dev/psaux”
# Option “Device” “/dev/ttyS0”
# Option “Device” “/dev/ttyS1”

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

# Option “Protocol” “Xqueue”

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

# Option “BaudRate” “9600”
# Option “SampleRate” “150”

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)

# Option “Emulate3Buttons”
# Option “Emulate3Timeout” “50”

# ChordMiddle is an option for some 3-button Logitech mice

# Option “ChordMiddle”

EndSection

# Some examples of extended input devices

# Section “InputDevice”
# Identifier “spaceball”
# Driver “magellan”
# Option “Device” “/dev/cua0”
# EndSection
#
# Section “InputDevice”
# Identifier “spaceball2”
# Driver “spaceorb”
# Option “Device” “/dev/cua0”
#
EndSection
#
# Section “InputDevice”
# Identifier “touchscreen0”
# Driver “microtouch”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “1412”
# Option “MaxX” “15184”
# Option “MinY” “15372”
# Option “MaxY” “1230”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection
#
# Section “InputDevice”
# Identifier “touchscreen1”
# Driver “elo2300”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “231”
# Option “MaxX” “3868”
# Option “MinY” “3858”
# Option “MaxY” “272”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonThreshold” “17”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section “Monitor”

Identifier “My Monitor”

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR’S
# USER MANUAL FOR THE CORRECT NUMBERS.

HorizSync 31.5 – 50.0

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR’S
# USER MANUAL FOR THE CORRECT NUMBERS.

VertRefresh 60

EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

Section “Device”
Identifier “VESA Framebuffer”
Driver “vesa”
#VideoRam 4096
# Insert Clocks lines here if appropriate
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the “-screen”
# option.
Section “Screen”
Identifier “Screen 1”
Device “VESA Framebuffer”
Monitor “My Monitor”

# If your card can handle it, a higher default color depth (like 24 or 32)
# is highly recommended.

# DefaultDepth 8
# DefaultDepth 16
DefaultDepth 24
# DefaultDepth 32

# “1024×768” is also a conservative usable default resolution. If you
# have a better monitor, feel free to try resolutions such as
# “1152×864”, “1280×1024”, “1600×1200”, and “1800×1400” (or whatever your
# card/monitor can produce)

Subsection “Display”
Depth 8
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 16
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 24
Modes “1024×768” “800×600” “640×480”
EndSubsection
Subsection “Display”
Depth 32
Modes “1024×768” “800×600” “640×480”
EndSubsection

EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# “-layout” option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section “ServerLayout”

# The Identifier line must be present
Identifier “Simple Layout”

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.

Screen “Screen 1”

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include “CorePointer”, “CoreKeyboard” and
# “SendCoreEvents”.

InputDevice “Logitech MX700” “CorePointer”
InputDevice “Keyboard1” “CoreKeyboard”

EndSection

P.S. Za tips and tricks i imwheel znam ali mi je nesto pravio probleme ne mogu da se setim zasto pa sam odustao od te opcije. Sta je taj xbind…. ?

Koji logovi vam trebaju?

[LYb]

Ne znam sta da ti kazem, em se ne razumem u TFT monitore, em mi config fajl deluje ok…

Nadam se da ce se neko pojaviti sa resenjem.

[popeye]

Xbindkeys, kako mu ime kaže, dodeljuje funkcije tasterima (na tastaturi i mišu). Pročitaj dokumentaciju (man xbindkeys) i biće ti jasno. Tamo ćeš naći i primere.

Koju grafičku koristiš?

[sanel_nbg22]

graficka intel on board chipset 852GME 64mb (shared)

[popeye]

Trebalo bi da imaš drajvere za grafičku (mislim da koristi i810), pa probaj njih, a isključi vesa framebuffer (možeš da probaš da oboriš rezoluciju i frekvenciju framebuffera) kako ti slika u konzoli ne bi treperila.

Drajvere takođe možeš naći i na Intelovom sajtu:

http://support.intel.com/support/graphics/sb/CS-010512.htm

http://downloadfinder.intel.com/scripts-df-external/filter_results.aspx?strTypes=all&ProductID=922&OSFullName=Linux*&lang=eng&strOSs=39&submit=Go%21

http://support.intel.com/support/graphics/linux/

[sanel_nbg22]

komandu xbindingkeys nemam a pokrenuo sam xorg conf i izabrao za graficku intel i810 i vise nemam onaj problem sa treperenjem .Isto tako mi sad radi i hotplug i sa lsusb je nasao logitech inc.
a ja mu nista nisam uradio 🙂 osim sto sam rekompajlirao kernel i ukljucio podrsku za HID 🙂

Zasto za protokol se koristi explorerps/2 ili imps/2 kad logitech ima protokol?

evo ako neko hoce da pogleda moj novi xorg.conf pa da mi kaze jel sam nesto zeznuo 🙂

[sanel_nbg22]

Problem treperenja sam resio ali sad mi recimo u configure desktop stoji da je refresh rate 0 ??
Zasto? Nervira me to 😆

Section “Module”
#***********************
Load “dbe” # Double buffer extension

SubSection “extmod”
Option “omit xfree86-dga” # don’t initialise the DGA extension
EndSubSection

Load “type1”
Load “freetype”
# Load “speedo”

Load “glx”

EndSection

Section “Files”
#*********************

RgbPath “/usr/X11R6/lib/X11/rgb”

# ModulePath “/usr/X11R6/lib/modules”

FontPath “/usr/X11R6/lib/X11/fonts/local”
FontPath “/usr/X11R6/lib/X11/fonts/misc”
FontPath “/usr/X11R6/lib/X11/fonts/75dpi:unscaled”
FontPath “/usr/X11R6/lib/X11/fonts/100dpi:unscaled”
FontPath “/usr/X11R6/lib/X11/fonts/Type1”
FontPath “/usr/X11R6/lib/X11/fonts/CID”
FontPath “/usr/X11R6/lib/X11/fonts/Speedo”
FontPath “/usr/X11R6/lib/X11/fonts/cyrillic”
FontPath “/usr/local/share/fonts”
EndSection

Section “ServerFlags”
#****************************

# Option “NoTrapSignals”
# Option “DontVTSwitch”
# Option “DontZap”
# Option “DontZoom”
# Option “DisableVidModeExtension”
# Option “AllowNonLocalXvidtune”
# Option “DisableModInDev”
# Option “AllowNonLocalModInDev”
# Option “blank time” “10” # 10 minutes
# Option “standby time” “20”
# Option “suspend time” “30”
# Option “off time” “60”
# Option “EstimateSizesAggresively” “0”

EndSection

# **********************************************************************
# Core InputDevice section
# **********************************************************************

Section “InputDevice”
#****************************

Identifier “Keyboard1”
Driver “kbd”
# Option “Protocol” “Xqueue”
# Option “AutoRepeat” “500 5”
# Option “Xleds” “1 2 3”
# Option “XkbDisable”
# Option “XkbModel” “pc102”
# Option “XkbModel” “pc105”
# Option “XkbModel” “microsoft”
# Option “XkbModel” “pc104”
# Option “XkbLayout” “de”
# Option “XkbVariant” “nodeadkeys”
# Option “XkbOptions” “ctrl:swapcaps”
# Option “XkbRules” “xorg”
# Option “XkbModel” “pc101”
# Option “XkbLayout” “us”
# Option “XkbVariant” “”
# Option “XkbOptions” “”

EndSection

Section “InputDevice”
#****************************

Identifier “Logitech MX700”
Driver “mouse”
Option “Protocol” “explorerps/2”
Option “Dev Name” “Logitech USB Receiver”
Option “Device” “/dev/mouse”
Option “Buttons” “8”
Option “ZAxisMapping” “4 5”

# Option “Protocol” “Auto”
# Option “Device” “/dev/psaux”
# Option “Device” “/dev/ttyS0”
# Option “Device” “/dev/ttyS1”
# Option “Protocol” “Xqueue”
# Option “BaudRate” “9600”
# Option “SampleRate” “150”
# Option “Emulate3Buttons”
# Option “Emulate3Timeout” “50”
# Option “ChordMiddle”

EndSection

# Some examples of extended input devices

# Section “InputDevice”
# Identifier “spaceball”
# Driver “magellan”
# Option “Device” “/dev/cua0”
# EndSection

# Section “InputDevice”
# Identifier “spaceball2”
# Driver “spaceorb”
# Option “Device” “/dev/cua0”
# EndSection

# Section “InputDevice”
# Identifier “touchscreen0”
# Driver “microtouch”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “1412”
# Option “MaxX” “15184”
# Option “MinY” “15372”
# Option “MaxY” “1230”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection

# Section “InputDevice”
# Identifier “touchscreen1”
# Driver “elo2300”
# Option “Device” “/dev/ttyS0”
# Option “MinX” “231”
# Option “MaxX” “3868”
# Option “MinY” “3858”
# Option “MaxY” “272”
# Option “ScreenNumber” “0”
# Option “ReportingMode” “Scaled”
# Option “ButtonThreshold” “17”
# Option “ButtonNumber” “1”
# Option “SendCoreEvents”
# EndSection

Section “Monitor”
#***********************

Identifier “TFT”

HorizSync 31.5 – 50.0
VertRefresh 60

# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies

EndSection

Section “Device”
#**********************
Identifier “Intel i810”
Driver “i810”
VendorName “Intel 810”
BoardName “Intel 810”
VideoRam 65536
# Insert Clocks lines here if appropriate
EndSection

Section “Screen”
#**********************
Identifier “Screen 1”
Device “Intel i810”
Monitor “TFT”
DefaultDepth 24

# DefaultDepth 8
# DefaultDepth 16
# DefaultDepth 24
# DefaultDepth 32

Subsection “Display”
Depth 8
Modes “1024×768” “800×600”
EndSubsection

Subsection “Display”
Depth 16
Modes “1024×768” “800×600”
EndSubsection

Subsection “Display”
Depth 24
Modes “1024×768” “800×600”
EndSubsection

Subsection “Display”
Depth 32
Modes “1024×768” “800×600”
EndSubsection

EndSection

Section “ServerLayout”
#*****************************

Identifier “Simple Layout”
Screen “Screen 1”
InputDevice “Logitech MX700” “CorePointer”
InputDevice “Keyboard1” “CoreKeyboard”

EndSection

[LYb]

Logitech ima specijalni protokol samo za svoje stare serijske miseve.

[Autor]

Članci