kako da diskonektujem softverski neki usb uređaj ?[REŠENO,VALJDA]

[dukenukem_4d]

U pitanju je usb miš ali i šire izgleda 🙁

Section “InputDevice”
Identifier  “Mouse0”
Driver      “mouse”
Option     “Protocol” “auto”
Option “ZAxisMapping” “4 5”
Option “Buttons” “3”
Option     “Device” “/dev/mouse”
Option     “ZAxisMapping” “4 5 6 7”
EndSection

[code]
root@wolvix tonymontano > lsusb                                               
Bus 004 Device 003: ID 0451:6001 Texas Instruments, Inc. AU5 ADSL Modem
Bus 004 Device 001: ID 0000:0000 
Bus 003 Device 001: ID 0000:0000 
Bus 002 Device 003: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse
Bus 002 Device 001: ID 0000:0000 
Bus 001 Device 003: ID 0951:160b Kingston Technology
Bus 001 Device 001: ID 0000:0000 
root@wolvix tonymontano >             
[/code]

cat /proc/bus/usb/devices

[code]
T:  Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.16 uhci_hcd
S:  Product=UHCI Host Controller
S:  SerialNumber=0000:00:10.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=  2 Ivl=255ms

T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0451 ProdID=6001 Rev= 1.00
S:  Manufacturer=TI
S:  Product=DSL Modem
S:  SerialNumber=00.20.E0.C4.C2.5E
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs=10 Cls=ff(vend.) Sub=00 Prot=00 Driver=ndiswrapper
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS=  8 Ivl=0ms

T:  Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.16 uhci_hcd
S:  Product=UHCI Host Controller
S:  SerialNumber=0000:00:10.1
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=  2 Ivl=255ms

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc= 93/900 us (10%), #Int=  1, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.16 uhci_hcd
S:  Product=UHCI Host Controller
S:  SerialNumber=0000:00:10.0
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=  2 Ivl=255ms

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=1.5 MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=046d ProdID=c00c Rev= 6.20
S:  Manufacturer=Logitech
S:  Product=USB Mouse
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=usbhid
E:  Ad=81(I) Atr=03(Int.) MxPS=  4 Ivl=10ms

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 6
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.16 ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:10.3
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=  2 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0951 ProdID=160b Rev= 1.00
S:  Manufacturer=Kingston
S:  Product=DataTraveler 2.0
S:  SerialNumber=000D882772755C880B12021A
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=31875us
[/code]

/usr/sbin/gpm -m /dev/mouse -t ps2
gpm -k ga zaustavlja

[code]
tonymontano@wolvix ~ > ls -o /dev/mouse
lrwxrwxrwx 1 root 5 Dec  8 17:03 /dev/mouse -> psaux
tonymontano@wolvix ~ > ls -o /dev/psaux                                       
lrwxrwxrwx 1 root 10 Dec  8 17:03 /dev/psaux -> misc/psaux
tonymontano@wolvix ~ > ls -o /dev/input                                       
total 0
crw-r–r– 1 root 13, 63 Dec  8 17:03 mice
crw-r–r– 1 root 13, 32 Dec  8 17:03 mouse0
tonymontano@wolvix ~ >                   
[/code]

[code]
tonymontano@wolvix ~ > cat /proc/bus/input/devices                           
I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
N: Name=”AT Translated Set 2 keyboard”
P: Phys=isa0060/serio0/input0
S: Sysfs=/class/input/input0
H: Handlers=kbd
B: EV=120013
B: KEY=4 2000000 3802078 f840d001 f2ffffdf ffefffff ffffffff fffffffe
B: MSC=10
B: LED=7

I: Bus=0003 Vendor=046d Product=c00c Version=0620
N: Name=”Logitech USB Mouse”
P: Phys=usb-0000:00:10.0-1/input0
S: Sysfs=/class/input/input2
H: Handlers=mouse0
B: EV=7
B: KEY=70000 0 0 0 0 0 0 0 0
B: REL=103
[/code]

kada se odkaci
[code]
usb 2-1: USB disconnect, address 2
[/code]

kada se opet utakne
[code]
usb 2-1: new low speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /class/input/input2
[/code]

e sad kako da se softverski dobije ovo da se otkaci ?

http://www.linux-usb.org/usbtest/

http://www.linux-usb.org/usbtest/testusb.c

http://www.linux-usb.org/usbtest/test.sh

moguce relevantno

http://www.mail-archive.com/[email protected]/msg52406.html

http://lxr.linux.no/linux+v2.6.16/Documentation/usb/

http://lxr.linux.no/linux+v2.6.16/Documentation/usb/proc_usb_info.txt

http://lxr.linux.no/linux+v2.6.16/Documentation/usb/hiddev.txt

http://lxr.linux.no/linux+v2.6.16/Documentation/usb/hotplug.txt

da li ima neka echo komanda u /sys/devices…. za ovo ???

ok sad se ublokirao i ndiswrapper 1.45 sa tiauxln (ndis-actiontec)
ili mi riknjava usb kontroler ili ovaj usb fles pravi
problem ostalim uredjajima na busu na starijim kernelima ???
(koliko sam  video nema prob ,na 2.6.18+ kernelima,a pocelo je da se javlja odkako mi je
prikacena usb fleska ??? hm verovatno je to nesto 😀 )

oot@wolvix tonymontano > lsmod                                               
Module                  Size  Used by
ndiswrapper          164048  0
bsd_comp                5632  0
ipt_LOG                6144  3
xt_tcpudp              3328  6
iptable_filter          2304  1
ip_tables              10968  1 iptable_filter
x_tables                9476  3 ipt_LOG,xt_tcpudp,ip_tables
ppp_synctty            7424  0
ppp_async              8704  1
crc_ccitt              1920  1 ppp_async
ppp_generic            24212  7 bsd_comp,ppp_synctty,ppp_async
slhc                    6272  1 ppp_generic
sc92031                13444  0
nvidia              4535316  12
ipv6                  229504  12
snd_seq_dummy          2948  0
snd_seq_oss            30080  0
snd_seq_midi_event      5888  1 snd_seq_oss
snd_seq                44496  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_pcm_oss            38432  0
snd_mixer_oss          15744  3 snd_pcm_oss
ohci_hcd              18436  0
via_agp                7680  1
shpchp                39616  0
usb_storage            78400  0
uhci_hcd              28688  0
ehci_hcd              29064  0
i2c_viapro              7572  0
i2c_core              16784  2 nvidia,i2c_viapro
snd_via82xx            22808  4
gameport              10888  1 snd_via82xx
snd_ac97_codec        86688  1 snd_via82xx
snd_ac97_bus            1920  1 snd_ac97_codec
snd_pcm                73864  4 snd_pcm_oss,snd_via82xx,snd_ac97_codec
snd_timer              19332  2 snd_seq,snd_pcm
snd_page_alloc          7688  2 snd_via82xx,snd_pcm
snd_mpu401_uart        6016  1 snd_via82xx
snd_rawmidi            18720  1 snd_mpu401_uart
snd_seq_device          6540  4 snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
snd                    44132  15 snd_seq_dummy,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore              7136  3 snd
via_rhine              19588  0
mii                    4864  1 via_rhine
pcmcia                30500  0
yenta_socket          23436  0
rsrc_nonstatic        11008  1 yenta_socket
pcmcia_core            34576  3 pcmcia,yenta_socket,rsrc_nonstatic
nls_utf8                1792  0
fuse                  33292  0
agpgart                28080  2 nvidia,via_agp
lp                      9800  0
parport_pc            24132  1
parport                30280  2 lp,parport_pc
psmouse                34952  0
nls_iso8859_2          4480  0
nls_iso8859_1          3968  1
nls_cp437              5632  1
unionfs                63136  1
squashfs              40628  17

Bilo koja sugestija je dobrodošla ,uključujući i ‘Uzmi veći čekić’
ili izvadi usb fleš totalno ???
EDIT:izgleda da nije usb memorija :-\ onda je usb modem ?

[dukenukem_4d]

ok ,mislim da je u pitanju sam miš :'(

[code]
lirc_dev: lirc_register_plugin: sample_rate: 0
usb 2-1: reset low speed USB device using uhci_hcd and address 2
usb 2-1: reset low speed USB device using uhci_hcd and address 2
usb 2-1: failed to restore interface 0 altsetting 0 (error=-71)
usb 2-1: USB disconnect, address 2
usb 2-1: new low speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input6
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 3
usb 2-1: new low speed USB device using uhci_hcd and address 4
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input7
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 4
usb 2-1: new low speed USB device using uhci_hcd and address 5
usb 2-1: device descriptor read/all, error -71
usb 2-1: new low speed USB device using uhci_hcd and address 7
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input8
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 7
usb 2-1: new low speed USB device using uhci_hcd and address 8
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input9
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 8
usb 2-1: new low speed USB device using uhci_hcd and address 9
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input10
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 9
usb 2-1: new low speed USB device using uhci_hcd and address 10
usb 2-1: new low speed USB device using uhci_hcd and address 11
usb 2-1: device not accepting address 11, error -71
usb 2-1: new low speed USB device using uhci_hcd and address 13
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input11
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 13
usb 2-1: new low speed USB device using uhci_hcd and address 14
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input12
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 14
usb 2-1: new low speed USB device using uhci_hcd and address 15
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input13
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 15
usb 2-1: new low speed USB device using uhci_hcd and address 16
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.0/input/input14
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.0-1
usb 2-1: USB disconnect, address 16
usb 2-1: new low speed USB device using uhci_hcd and address 17
usb 2-1: new low speed USB device using uhci_hcd and address 18
usb 2-1: device descriptor read/64, error -110
usb 2-1: device descriptor read/64, error -110
usb 2-1: new low speed USB device using uhci_hcd and address 19
usb 2-1: device descriptor read/64, error -110
usb 2-1: device descriptor read/64, error -110
usb 2-1: new low speed USB device using uhci_hcd and address 20
usb 2-1: device not accepting address 20, error -110
usb 2-1: new low speed USB device using uhci_hcd and address 21
usb 2-1: device not accepting address 21, error -110
usb usb2: Controller not stopped yet!
usb 2-2: new low speed USB device using uhci_hcd and address 22
usb usb2: Controller not stopped yet!
usb 4-1: new low speed USB device using uhci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.2/usb4/4-1/4-1:1.0/input/input15
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.2-1
usb 4-1: USB disconnect, address 2
usb 4-1: new low speed USB device using uhci_hcd and address 3
usb 4-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.2/usb4/4-1/4-1:1.0/input/input16
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.2-1
usb 4-1: USB disconnect, address 3
usb 4-1: new low speed USB device using uhci_hcd and address 5
usb 4-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.2/usb4/4-1/4-1:1.0/input/input17
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.2-1
usb 4-1: USB disconnect, address 5
usb 4-1: new low speed USB device using uhci_hcd and address 6
usb 4-1: configuration #1 chosen from 1 choice
input: Logitech USB Mouse as /devices/pci0000:00/0000:00:10.2/usb4/4-1/4-1:1.0/input/input18
input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.2-1
usb 4-1: USB disconnect, address 6
[/code]

naime na novijeim kernelim 2.6.20+ odprilike ,kernel ga sam softverski rekonektuje
tako da su mi  prolazile neprimećene karatke pauze ,zastajkivanja
a na starom kernelu se zaglupi (mora ručno da se restartuje usbhid)
ali je sad totalno prestao da mi radi…

a nešto mu je kabli u prekidu neka linija ,ili je miš otišao na njemu neki čip
ili tranzistor,mislim da je to ??? banalan razlog

jao ko da su mi odsekli levu ruku… ili uzeli džeferdar… 😀
sad sam stavio običnog miša koji nema srednji taster :'(

Q:
jel da lemim kabli od usb miša ili da ga bataljujem potpuno ,sa opravkom ? ???

[tomaja]

A:
Ne isplati se popravljati osim ako nije neki extra skupi model u pitanju,
pa i onda je pitanje da li ćeš išta uspeti da uradiš.

linux4life

[dukenukem_4d]

Hvala na odgovoru O0
Mislim da si u pravu , običan je miš u pitanju , sa 3 tastera i točikićem,optički
(sada su dosta pristupačni po ceni)

ali nisam još uvek utvrdio sa sigurnošću da li je miš
postoji još mogućnost da otkazuje uhci kontroler na ploči :-
najbolje da još ne lemim za sada ništa

a čudno je što istovremeno ehci usb2.0 radi punom parom ,paralelno ???
(a kada se ovo ublokira sa mišem onda otkaže poslušnost cela ta fizička grana
😀 do sledećeg restarta )

da li ima još neki log u kome može da se još nešto vidi ,ili da se uključi debug  za usb,nego to ne znam još uvek kako ???
(stavljao sam i drugog usb miša i on isto otkaže ali na drugom kompu radi
ali nisam siguran taćno kako je išao taj test )

[dukenukem_4d]

е ,ипак је био миш ,
погледао сам оне логове и реко ,горе не може да буде
па сам мало скратио кабли и пажљиво излемио на онај конектор
мада нисам беш задовољан ,пре бих ставио други конектор
али нисам сигуран да ли имају негде празне контакте 😀
(ваљда неће да се направи спој неки ,али није баш за војну употребу сада)
било би боље да су нови контакти

значи ипак се прецвиковао кабли на улазу у миша

баш ме занима колико може да му издржи ова црвена диода
јер и сад малтене ради као кад је купљен (није био од најскупљих
већ када су били мало јефтинији)
после око 1 год заменио сам му микропрекидаче са неким јапанским
који и после 5 год и даље кликћу  😀 😀 😀
(али се мало изјела горња пластика на главном дугмету ,па му то мало фали сада)
осим тога од сервисирања прилепио сам недавно силиконске пдлошке са супер лепком O0

за сада пар дана ради опет лепо ,ваљда ???

[Аутор]

Чланци