Ћирилица

[EddyNS]

u kdm.log-u na kraju sam nasao ovo

Fatal server error:
Server is already active for display 0
If this server is no longer running, remove /tmp/.X0-lock
and start again.

I sad nesto razmisljam, da li je mogucje da mi se signal salje na drugi izlaz graficke kartice(taj je dvi nemam nikakav adapter pa ne mogu probati)

[EddyNS]

E zaboravio sam da napisem da sad sa ovim drajverom, kad se pojavi onaj Hz=? sa zvucnika cujem start up system melodiju ili kao se to vecj zove u linuxu.
prilozeni zip sadrzi sve log fajlove koje sam nasao u /var/log

[EddyNS]

Upgrade-ovao sam ati drajver iz synaptica(nakon njegovog reload-a), ovo cudo ni dalje ne radi kako treba, tj. jos uvek moram rucno podesavati onaj Drake.
Prilog novi Ati sadrzi ono sto sam malopre prekopirao iz zavrsene instalacije, neki report.
A u onom drugom (log file) sam primetio sledecje
fglrx: no matching device section for instance (  ) found

[EddyNS]

Da, mogucje da je izmesano onaj run file je 8.40.4 a synaptic je instalirao 8.39.4
Jel mogu nekako proveriti da li su oba instalirana, ili eventualno jel mogu nekako da izbrisem oba i da posle ponovo skinem sa synapticom onaj koji treba?
sad sam reloadovao synaptic. U njemu kad ppred neke stavke stoji zvezda, jel to znaci da je dostuoan upgrade?

[EddyNS]

I jos jednom:
sa vlasnickim drajverima ne radi a radio je
Pokrenem safeboot pa drakeconfig – display – ati (fglrx) – test: an error ocured: (EE) no devices detected!
Ovo isto se desava i ako izaberem i radeon (u dysplay driver meniju) a 95% sam siguran da je nakon instalacije drajvere ova stavka radila.
Test radi samo sa opcijom ati radeon (vesa) pa ostavim da bude ovaj.
ukucam startx pa krenem da pokrenem ati catalyst control center, i dobijem poruku:
there was a problem initializing cat.con.cen.:
No ati graphics driver installed, or the ati driver is not functioning properly
Plese install the ati driver appropriate for your hardware, or configure using aticonfig (gde se nalazi ovaj aticonfig???)

[EddyNS]

http://linux.wordpress.com/2007/04/11/amd-knowledge-base-ati-linux-drivers/

    737-26907: Unsupported Features with ATI Linux Drivers

    The information in this article applies to the following configuration(s):

        * AIGLX
        * Beryl
        * Compiz
        * MythTV
        * TV TIME
        * Linux 8.19 Driver and higher
        * openSUSE
        * SUSE LINUX Enterprise Desktop (SLED)
        * SUSE LINUX Enterprise Server (SLES)
        * Red Hat Enterprise Linux Workstation (RHEL-WS)
        * Red Hat Enterprise Linux Advanced Server (RHEL-AS)
        * Red Hat Enterprise Linux Enterprise Server (RHEL-ES)

    Symptoms:
    The following features are not supported with ATI Linux drivers.

        * AIGLX, Beryl, Compiz, MythTV, TV TIME

OK, nagovorili ste me naucicju da sviram (iako nemam sluha za to)

[EddyNS]

ovo sam nasao na adresi: http://www2.ati.com/drivers/linux/linux_8.12.10.html#172579

X Fails to Load on Systems with Linux Kernel Version 2.6.x

This information applies to the following system configurations:

    * Linux kernel version 2.6.x
    * Any ATI Linux driver

A blank screen may appear momentarily when X starts to load. The following error message (or similar) may appear on the text console or in /var/log/XFree86.0.log:
(EE) fglrx(0): [agp] unable to acquire AGP, error “”xf86_ENODEV””xf86_ENODEV””

This is not a problem with the display driver.

Version 2.6 kernels require a second kernel module in addition to agpgart, which should be named similar to the manufacturer of your motherboard AGP chipset. This error message should occur if the other agp module is not loaded.

This issue can be worked around as follows:

  1. First make sure that agpgart is loading properly.
  2. To find out which AGP controller your motherboard uses, issue the following command: lspci | grep AGP
  3. To find a list of AGP related kernel modules installed on your machine, issue the following command and look for a module (*.ko file) that suits your AGP Controller: ls /lib/modules/`uname -r`/kernel/drivers/char/agp
  4. Use the modprobe command (as root) to load the module. For example: On a motherboard using a VIA® AGP Controller, you would load the via-agp.ko using modprobe as follows (notice that the trailing .ko is omitted): modprobe via-agp

Check the modprobe manpage for more information on loading kernel modules.

  5. To verify that the AGP module is already loaded, run lsmod as root. With the X server running and the connection established, the usage count of this module must be greater than zero.

If you cannot find a suitable agp module for your motherboard, then you may want to upgrade to the latest version of the Linux kernel, or check your motherboard manufacturer’s website for more information.

mij ATI je pci-e, ako to znaci nesto. A i negde sam nasao da atijevi drajveri imaju ogromnih problema sa openGl-om.
Da li da naucim da sviram harmoniku i stojim na ulici svirajucji dok ne skupim pare za nvidiu ili mislite da ima nade?

[EddyNS]

ima listinga i uctitava se linux (kad stisnem Esc za verbose mode, za sve pise da je ok), i mislim da se to desi kad ucitava atijev fglrx

[EddyNS]

Ponovo se umesto login screen-a javlja onaj Hz=? u malom pravougaoniku (kao kad ispise “No signal” kad nije monitor ustekan u graficku)
Gledao sam i onaj conf fajl, cini mi se da je u redu.
I kad u Xfdrakeu biram graficku, na kraju kazu da su vlasnicki drajveri instalirani i da li zelim njih koristiti.
Napominjem da se ovo nije desavalo sve dok nisam pokrenuo beryl (mada da sam restartovao masinu mozda bi se i desilo)

Kako da namestim ovo, a da ne moram svakii put u safeboot – xfdrake

[EddyNS]

nekako sam namestio. Kako da proverim da li postoje neki konflikti ili nesto slicno?? Ako razumete na sta mislim.

Gde mogu skinuti kodeke jel znate neki sjt sa uputsvom za to?

A da i monitor mi radi na iritantih 60 hz i ne mogu podesiti na 75 jel ima neko neku ideju?

[Аутор]

Чланци