Početak›Forumi›Linuks›Linuks umrežavanje›ADSL MANDRIVA POMOC!!!
- This topic has 61 odgovor, 7 glasova, and was last updated 16 years, 7 months ranije by sdfasfasffsdqqfdq.
-
AutorČlanci
-
1. septembar 2007. u 1:41 am #9153rellikUčesnik
Nov sam totalno u radu sa linuksom, mnoge stvari kontam i jednostavne su ali nikako ne mogu da napravim konekciju za internet!!! :'( Provajder je neobee, modem asus aam6000ug (USB) a linux mandriva 2006. Citao sam i trazio al ne mogu nista da nadjem ili bar da skontam kako se radi? :redface:
Pomozite please 😀
1. septembar 2007. u 6:18 am #61098tomajaGlavni majstorAko ti Mandriva nije prepoznala modem skini i instaliraj drajver sa
http://sourceforge.net/projects/aam6000ug
a zatim podesi konekciju iz Mandriva Kontrolnog Centra (mcc) , tab “Network & Internet”linux4life
1. septembar 2007. u 5:17 pm #61099rellikUčesnikU sustini je prepoznat kao sagem i radi mu lampica, al konekciju nikako ne mogu da napravim da radi, a skinuo sam i te drivere ali ne znam kako da ih instaliram!!! :redface: :redface: :'( :redface: :redface:
1. septembar 2007. u 5:25 pm #61100sdfasfasffsdqqfdqUčesnikAko si kod neobee-a onda se sigurno konektujes preko pppoe, kucaj u konzoli
su
pppoe-setup – tu vrsisi konfiguraciju konekcije!
pppoe-start – konektujes se na internet
pppoe-stop – diskonektujes se sa interneta
pppoe-status – status linka za internet (valjda ???)1. septembar 2007. u 6:08 pm #61101rellikUčesnikU medjuvremenu se tu pojavila i neka ethernet kartica, i on sada kao sam podesio nesta ali ne ostvari konekciju ,a na modemu pokazuje da ima konekciju i cak nekad da se salju podatci, ali browser ne radi !!!
A probao sam i ovo:
Welcome to the Roaring Penguin PPPoE client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly…Looks good! Now, please enter some information:
USER NAME
>>> Enter your PPPoE user name (default [email protected]): [email protected]
INTERFACE
>>> Enter the Ethernet interface connected to the DSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where ‘n’ is a number.
(default eth0): /dev/hme0Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter ‘no’ (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no): 3DNS
Please enter the IP address of your ISP’s primary DNS server.
If your ISP claims that ‘the server will provide DNS addresses’,
enter ‘server’ (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:PASSWORD
>>> Please enter your PPPoE password:
>>> Please re-enter your PPPoE password:FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose ‘NONE’ and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.The firewall choices are:
0 – NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 – STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 – MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2): 1** Summary of what you entered **
Ethernet Interface: /dev/hme0
User name: [email protected]
Activate-on-demand: Yes; idle timeout = 3 seconds
DNS: Do not adjust
Firewalling: STANDALONE>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
(But first backing it up to /etc/ppp/pap-secrets-bak)
(But first backing it up to /etc/ppp/chap-secrets-bak)Congratulations, it should be all set up!
Type ‘pppoe-start’ to bring up your PPPoE link and ‘pppoe-stop’ to bring
it down. Type ‘pppoe-status’ to see the link status.
[root@localhost ~]# pppoe-start
[root@localhost ~]# pppoe-start
pppoe-start: There already seems to be a PPPoE connection up (PID 5401)
[root@localhost ~]# pppoe-status
Note: You have enabled demand-connection; pppoe-status may be inaccurate.
pppoe-status: Link is up and running on interface ppp0
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.112.112.112 P-t-P:10.112.112.113 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:0 (0.0 b) TX bytes:40 (40.0 b)[root@localhost ~]# pppoe-start
pppoe-start: There already seems to be a PPPoE connection up (PID 5401)
[root@localhost ~]# pppoe-stop
Killing pppd (5548)
Killing pppoe-connect (5401)
[root@localhost ~]#Ali nece, gde sam pogresio ???
1. septembar 2007. u 6:39 pm #61102dukenukem_4dUčesnikdefault eth0): /dev/hme0
ovde bi trebalo da ide eth0 ili eth1 ili u slucaju usb modema obicno nas0
ili nesto trece za amedyn, a to trece moze da se sazna kada otkucas
kao root
[code] ifconfig [/code]
to je na pocetku bloka texta i nije lo ,(lo je loopback)treba posle i one DNS adrese da se unesu ,za neobee bi moglo negde u win da se vidi
koje su ili ima na cd-u u nekom konfiguracionom fajlu(e uzmi uj svoju adresu u prethodnom postu ,oni roboti non stop pretrazuju forum)
1. septembar 2007. u 6:41 pm #61103sdfasfasffsdqqfdqUčesnikja samo unosim username i pass a za sve ostalo opicim Enter! i tako mi radi! 🙂
1. septembar 2007. u 8:52 pm #61104rellikUčesnik[quote]default eth0): /dev/hme0
ovde bi trebalo da ide eth0 ili eth1 ili u slucaju usb modema obicno nas0
i[glow=red,2,300]li nesto trece za amedyn, a to trece moze da se sazna kada otkucas
kao root[/glow]
[code] ifconfig [/code]
to je na pocetku bloka texta i nije lo ,(lo je loopback)treba posle i one DNS adrese da se unesu ,za neobee bi moglo negde u win da se vidi
koje su ili ima na cd-u u nekom konfiguracionom fajlu[glow=red,2,300]
(e uzmi uj svoju adresu u prethodnom postu ,oni roboti non stop pretrazuju forum)[/glow]
[/quote]Ne kontam kako ??? ^^^^^^
1. septembar 2007. u 9:41 pm #61105dukenukem_4dUčesnikgledaj ,ono u konzoli sto pise lo ppp0 to su mrezni adapteri
ali nazalost na screenshotu ne vidim sta je ispred toga ,tj da li je
neka mrezna (eth1) ili ovaj usb modem (nas0)
ako mozes da kazes da li si onaj drajver kompilirao iz tar.gz arhive
i da li mu ucitavs firmware,tj kojim postupkom ides?jer kod bl4ck doom je drugi tip modema ,kod ovog treba i nekakv firmware
da se ucitava,pre nego sto se pppoe-start uradi1. septembar 2007. u 10:07 pm #61106rellikUčesnikJa nisam nikakve drivere instalirao, on ga je prepoznao kao sagem … (kompatibilni su) a nakon restarta je sam stvorio neku enthernet karticu!!!
Note: You have enabled demand-connection; pppoe-status may be inaccurate.
pppoe-status: Link is up and running on interface ppp0
ppp0 Link encap:Point-to-Point Protocol
inet addr:10.112.112.112 P-t-P:10.112.112.113 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:0 (0.0 b) TX bytes:40 (40.0 b)[root@localhost ~]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:F2:4D:11:EE
inet6 addr: fe80::215:f2ff:fe4d:11ee/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:65535 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:2430 (2.3 KiB)lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:601 errors:0 dropped:0 overruns:0 frame:0
TX packets:601 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:67111 (65.5 KiB) TX bytes:67111 (65.5 KiB)ppp0 Link encap:Point-to-Point Protocol
inet addr:10.112.112.112 P-t-P:10.112.112.113 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:0 (0.0 b) TX bytes:40 (40.0 b) -
AutorČlanci
Moraš biti prijavljen da bi postavio komentar u ovoj temi.